background image

What to do in the event of an appliance 
fault or breakdown:

Step 1:

Always contact your installer or commissioning 

engineer in the first instance, who must

thoroughly check all his work PRIOR to

requesting a service visit from Trianco.

Step 2:

If your appliance has developed an in-guarantee

fault your installer should contact Trianco

for assistance.

What happens if may installer/engineer is
unavailable?

Step 3:

Contact Trianco Direct.  We will provide you with

the name and telephone number

of our

Service Agent.  However, a charge may apply if

the fault is not covered by the appliance 

guarantee (payment will be requested on site by

our independent Service Agent).

PLEASE NOTE:

Unauthorised invoices for attendance and repair work

carried out on this appliance by any third party will not be

accepted by Trianco.

A step by step guide to reporting a fault
with your appliance

A qualified field SERVICE ENGINEER is available to

attend a breakdown or manufacturing fault occurring

whilst the appliance is under guarantee.

No charge will be made for parts and/or labour
providing:

An appliance fault is found and the appliance has

been installed and commissioned within the past 12

months. Reasonable evidence of this must be

supplied on request.  

A charge will be made where:

Our Service Engineer finds no fault with the

appliance (see note below).

or

The cause of a breakdown is due to other parts of the

plumbing/heating system (including sub-standard or

incorrect fuel type), or with equipment not supplied 

by Trianco.

or 

The appliance is outside the manufacturer’s guarantee

period (see terms and conditions).

or

The appliance has not been correctly installed,

commissioned or serviced as recommended (see

commissioning, installation and service

instructions)

or

The breakdown occurs immediately following an 

annual service visit. In this instance your appointed 

Service Agent must check all his work PRIOR to 

requesting Trianco to attend.

or

When a service engineer fails to find a fault with 

the boiler, or if other parts of your heating system, 

other than the boiler, are faulty.

TRIANCO

CUSTOMER AFTER SALES SERVICE INFORMATION

SERVICE CENTRE AND TECHNICAL SUPPORT

Tel: 0114 257 2300  Fax: 0114 257 2338

Hours of business Monday to Thursday 8.30am - 4.45pm

Friday 8.30am - 2.30pm

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание TRG 45



















Отзывы: