Trevi Outline Скачать руководство пользователя страница 8

Страница: 8 / 16

1. Remove handles. (see Pages 10/11 for details)

2. Remove the front cover plate (1) by prising

forward using the small slots at the sides of

the front cover plate.

3. Remove the two cover plate screws and pull

off the back cover plate (2).

4. Remove the volume control handle (6) and

carrier (10) by unscrewing screw (8b) and

pulling off.

5. Pull off shroud (9)

6. Remove the two gear box cover fixing

screws and pull off the gear box cover (11).

7. Pull out the drive shaft (15)

8. Loosen the two cartridge cone screws and

remove the gear/clutch wheels (16) by

pulling forward.

9. Lift off the rear gear box cover (17)

10. Isolate the shower valve from the supplies

and unscrew the two cartridges (18)

anticlockwise

11. Fit the flushing adapter (25) in place of the

cartridges in turn and flush the pipework.

12. Assemble the valve in reverse order.

13. If fitting replacement cartridges and/or

clutches they should be fitted at this stage.

14. Both cartridges must be in the closed

position before fitting the gear clutches (16)

in position.

CARTRIDGE REPLACEMENT

Flushing and replacement of cartridges & gear clutch wheels

Figure 10

VALVE REPLACEMENT

trevi showers.qxd 04/12/03 13:21 Page 8

Содержание Outline

















Результаты поиска

Содержание Outline

Отзывы:

Похожие инструкции для Outline

Бренды по названию

Популярные бренды

Trevi Outline, Руководство по установке

Результаты поиска

Содержание Outline

Отзывы:

Похожие инструкции для Outline

Бренды по названию

Популярные бренды