Trends Combo 12 Desktop Hi-Fi System User Guide
Section 9. Troubleshooting / Section 10. Accessories
15
9
9
.
.
T
T
r
r
o
o
u
u
b
b
l
l
e
e
s
s
h
h
o
o
o
o
t
t
i
i
n
n
g
g
If your Trends Combo 12 is out of order, it may not be very serious. Before you call
your local distributor or us to repair, you are suggested to check the following:
Symptoms
Possible Reasons
Handling Methods
power cords not properly
connected
properly connect the power
cords
cannot power ON
indicator not bright
power switch is OFF
switch ON the power
the volume level is too low
turn volume level higher
the audio cable not properly
connected
properly connect the audio
cable
the audio source (e.g. CD
player) not started playing
start playing the audio
source
wrong input is selected
check input selection
no sound at all
the speaker cables not
properly connected
properly connect the
speaker cables
sound out(s) out
loose connection
check input and output
connections. When all has
been double-checked
reduce volume and switch
unit back on
the Input voltage is very low
Check that the input voltage
is 120V or 220 V, (specific
model should be selected,
not compatible)
The output voltage is 0 V or
very low
The unit is in current limit
condition due to overload
caused by large reactive
loading r by the output being
short circuited
Check the output terminals
are not shorted. Remove
the load. If the output
voltage gets restored, the
load is shorted or is offering
large reactive impedance
AC side fuse blows as soon
as power is turned on.
Unit is defective
Call technical support or by
email
[email protected].
1
1
0
0
.
.
A
A
c
c
c
c
e
e
s
s
s
s
o
o
r
r
i
i
e
e
s
s
·
3 Pins Power Cord x 1 pcs (IEC plug and another plug with different country
standards)
·
User Guide x1
·
Warranty Card x1
Trends Combo 12 Desktop Hi-Fi System User Guide
Section 11. Regulatory Compliance / Section 12. Contact Us
16
1
1
1
1
.
.
R
R
e
e
g
g
u
u
l
l
a
a
t
t
o
o
r
r
y
y
C
C
o
o
m
m
p
p
l
l
i
i
a
a
n
n
c
c
e
e
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
1
1
2
2
.
.
C
C
o
o
n
n
t
t
a
a
c
c
t
t
U
U
s
s
ITOK Technologies Limited (Trends Audio)
Address : Rm. K, 11/F, Kwun Tong Industrial Centre, Phase 1
472-784 Kwun Tong Road, Kowloon, Hong Kong
Tel
: +852 2304 0730 (9am-6pm, GMT+8:00)
Fax
: +852 2566-5740
: [email protected] (Marketing)
[email protected] (Technical Support)
Website : http://www.TrendsAudio.com
