TRENDnet TPE-P521ES Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 68

TRENDnet TPE-P521ES Скачать руководство пользователя страница 28

© Copyright 2018 TRENDnet. All Rights Reserved.

TRENDnet User’s Guide

TPE-P521ES

25

In the Loopback Detection table, select one of the Loopback Detection Status choices
from the pull down menu:



Enabled: This selection enables the Loopback Detection feature for each port.
This state must be enabled along with the Status field at the top of the page
before this feature can be active on the selected port.



Disabled: This selection disables the Loopback Detection feature on the
selected port.

Next to each entry modified, under the Action column, click Apply to save the changes.

NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:

1.

From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.

2.

Click Continue to return to the Web Configuration of your switch.

«
...
26
27
28
29
30
...
»

Содержание TPE-P521ES





































































Отзывы:

Нет отзывов