background image

T5

-17-

MAINTENANCE AND CARE

Cleaning

I

Keep the machine clean at all times.  Some
maintenance products and solvents may
damage the plastic parts, these include
products containing Benzene, Trichloroethyle
Chloride and Ammonia.

I

Never use any caustic agents to clean the
plastic parts.

Ensure machine is isolated from
power supply.

It is advisable to have the 
brushes replaced by an
authorised Trend Service Agent.
The router will also be given a
thorough inspection.

I

Undo the single screw (1) in the top of the
vent housing.  Slide the vent housing (2) off.

I

Pull back the spring retaining clip (4).  Take
care not to bend or distort the coil spring. 

I

Disconnect the wire (5) and remove the
carbon brush (6). 

I

Insert the new brush and press the connector
firmly on to the tag (3).  Refit the cover.

I

Always use original T5 spare parts.

Changing Brushes

Lubrication

I

The bearings of the machine need no
lubrication, as they are sealed.  The two
plunge columns on the routing base should
be slightly oiled from time to time.

I

Keep the cooling vents on the motor housing
clean and unobstructed at all times.  Blow out
any dust and dirt at regular intervals.

I

Visually check the carbon brushes.  In the
event of excessive sparking, they may need
changing.

I

After about 40 operating hours inspection by
a authorised Trend Service Agent is
recommended.

ENVIRONMENTAL PROTECTION

Recycle raw materials instead of disposing
as waste.

Accessories and packaging should be sorted for
environmental-friendly recycling.

Separate collection.  This product must
not be disposed of with normal
household waste.

Household User

Local regulations may provide for separate
collection of electrical products from the
household, at municipal waste sites or by retailer
when you purchase a new product.

Please call Trend Customer Services for advice
as to how to dispose of unwanted Trend
electrical product in an environmentally safe way
or visit www.trend-uk.com

Business User

Please call Trend Customer Services for
disposal of unwanted Trend electrical products.

GUARANTEE

The unit carries a manufacturers guarantee in
accordance with the conditions on the enclosed
guarantee card.

For the location of your nearest Trend Service
Agent, please call Trend Customer Services or
see Stockist Locator at www.trend-uk.com

4

3

1

2

5

6

MANU/T5 v9.0  19/2/09  13:10  Page 17

Содержание T5MK V2























Отзывы: