Trelawny LPS55, Руководство по эксплуатации и обслуживанию

Страница: 7 / 8

PART NUMBERS
All rights reserved. Any unauthorised use or copying of the contents or part thereof is prohibited.
This applies to trademarks, model denominations, part numbers and drawings.
Use only genuine Trelawny spares.
The use of non-Trelawny spare parts invalidates the warranty.
TROUBLE SHOOTING
Low air pressure. Ensure that the air pressure is correct at 90psi, max 100psi. Poor performance or lack of
power
If tool has been left for some time without use, the
oil may dry out slightly causing a sticky residue.
Strip tool down and re-oil.
Tool worn out, can you feel excessive side ways
movement between the piston and cylinder bore.
Replace the piston and cylinder, along with a new scraper seal.
Cutterhead worn out. Replace cutterhead
Applying to much down force. Only apply sufficient down force to stop the tool from bouncing.
Tool continues to run with
trigger released
Valve seal may have become dislodged through the
tool being disconnected with the trigger in the open
position.
Ensure that the trigger has not been taped or wired in the open
position.
Do not use quick release couplings to switch tool off.
Cutterhead seized on piston If the tool has been laid up or used with water
present, rust may have built up between the piston
and cutter.
In extreme cases it may be necessary to apply heat to release
the cutter head, otherwise a releasing agent may be sufficient.
Item
No
Part No Description Item
No
Part No Description
1 411.5011 Body 17 843.0765 3/4” Claw coupling
2 613.5001 Cylinder 18 819.5020 90° Adapter
3 809.6599 Cylinder O’Ring (Small) 19 627.5011 Adaptor (Spring seat)
4 809.6619 Cylinder O’Ring (Large) 20 627.5012 Spring Seat
5 829.5001 Wiper Seal 21 712.5001 Valve Spring
6 612.5005 Piston (Pin Fit) 22 809.5599 Valve Stem Seat O’Ring
612.5001 Piston (Screw Fit) 23 809.0069 Valve Stem Seal O’Ring
7 441.5359 TCT tip 5 point Scabbler Head (Pin fit) - inc pin 24 618.5025 Valve Stem
441.5360 TCT tip Cruciform Scabbler Head (Pin fit) i- nc pin 448.5025 Valve Stem - including O’Rings
441.5369 TCT tip 9 point Scabbler Head (Pin fit) - inc pin 25 813.0636 Roll Pin
426.5051 TCT tip 5 point Scabbler Head (Screw fit)
426.5052 TCT tip Cruciform Scabbler Head (Screw fit) Not shown in exploded view
809.6499 Piston O’Ring (Screw fit)
8 813.1050 Spirol Pin (Pin fit heads) 450.5001 100 x 100 Compactor Foot (Screw fit)
450.5011 100 x 100 Compactor Foot (Pin fit)
9 624.5011 Main Shaft 450.5003 127 x 152mm Compactor Foot (Screw fit)
10 625.5012 Locknut (Main shaft) 450.5013 127 x 152mm Compactor Foot (Pin fit)
10a 810.9003 Sealing Washer 450.5006 100 x 200mm Compactor Foot (Screw foot)
11 665.5011 Trigger Guard 450.5016 100 x 200mm Compactor Foot (Pin foot)
12 649.5011 Throttle Lever 450.5007 127 Diameter Compactor Foot (Screw fit)
13 822.2000 Rubber Grip 450.5017 127 Diameter Compactor Foot (Pin fit)
14 422.5005 Valve Body 852.0812 Trigger Guard Screw
15 634.5015 Blanking Cap
16 625.5011 Locknut (Valve body handle)