Pag. 3
Pag. 3
TECHNICAL CHARACTERISTICS
-
Power input: 230Vac. 50/60Hz
-
Backup battery: 3.7V Rechargeable Lithium (3 hours standby time)
-
PIR detector: Wide angle: 100° 12 mt.
-
Standby current: <40mA Working current <45mA.
-
Transmission frequency: 433.92 Mhz.
-
Camera: 1/6.5” OV CMOS chip: 300,000 pixel.
-
Video format: AVI
-
Recording speed: 30 fps.
-
Resolution: 640 x 480 x Min. Illumination: 0.1 lux.
-
Focal length: 8mm.
-
View Angle: 35° vertical 60° horizontal.
-
Transmission Mode: USB 2.0 (Hs)
-
Recording time: 3 Minutes
-
Memory card capacity: 4 Gb
-
Product dimensions: 103 x 60 x 32mm.
INSTALLATION INSTRUCTION & FUNCTIONS:
-
Fixing the DVR-6:
Fix the swivel bracket support onto the wall surface at a height that rages from 1.8 to 2.5
meters form the floor. Fix the swivel bracket to the DVR-6 and adjust it so it will be able to detect movement
and at the same time have a good angle position to record a burglary events.
-
DVR-6 Start-up:
Connect the power supply and switch the DVR-6 to “ON” by pushing the small switch, to the
right with a pointed object. See fig. 3 page 4. A red LED will light and after 30 seconds will go
“OFF”
. The
DVR-6 is now in standby mode.
-
Setting Date and Hour:
Connect with the USB cable the DVR to your PC. Select
“DEVICES“
in
“MY
COMPUTER” and
activate
“GetSysTime”.
The DVR-6 will automatically learn the date and hour of your PC.
-
Arming/Disarming the DVR-6:
This product is specially designed to function with all Tre i Systems “Pegaso”
protocol control panels and is armed and disarmed by the panel at the same time in which the panel is arm
and disarmed. The DVR-6 will emit a beep as indication that it has received the arming command and after an
8 second delay time it will automatically arm. When it is disarmed, the unit will emit 2 beeps.
-
Automatic recording:
When the DVR-6 on-board PIR sensor triggers an alarm, the control panel with which
it has been installed will be triggered and at the same time the DVR-6 will start 3 Minute Audio/Video
recording of the protected area with date and time. This event will be memorized on the internal SD card.
During this recording a RED LED will flash. After the control panel is Disarmed, on the DVR-6 a Blue LED will
light for 50 seconds to indicate that a recording has taken place.
-
Recording Playback: (A)
To visualize the recording, with the DVR-6 disarmed, remove the SD card and
insert it into your computer. After the recording has been seen, insert once again the SD card into the DVR-6.
-
Recording Playback: (B)
You may also visualize the recording in the DVR-6 without removing the SD card.
Follow this procedure: On the back side of the DVR-6 switch to “OFF” the battery backup switch. From the
power supply, connected to the A.C. outlet, remove the USB cable and insert it directly into your computer to
see the event recorded. After having visualized the recording, reconnect the USB cable to the power supply.
-
More than 1 DVR-6 installed :
If an installer or an end user wishes to recorded events in different areas in a
home, store, factory etc. more than one DVR-6 may be installed and each will record events individually in
the areas it is protecting. Also each DVR-6 will act as a normal PIR volumetric sensor and protect the area
In which it is installed.
