background image

2 • SLAYER PRO 4X4

INTRODUCTION

Thank you for purchasing a Traxxas Slayer Pro 4x4. The Slayer Pro 
4x4 is designed to simulate the speed and excitement of full-scale 
Pro 4X4 short-course race trucks. 4WD Short Course Racing brings 
together the most horsepower and the most suspension travel 
for incredible side-by-side, fender-banging racing action. Engines 
scream at the redline as dirt and rocks roost from all four tires. Only 
the fastest, most powerful trucks dare to compete! The Traxxas 
Slayer Pro 4x4 brings the sound, smell, and excitement of  Pro 4X4 
short-course racing right into your own backyard. 

The TRX 3.3 Racing Engine is the most powerful engine of its size 
ever available in a Ready-To-Run truck. Advanced engineering and 
design, along with thousands of hours of testing, puts the TRX 3.3 
in a class by itself. Each part of the TRX 3.3 - from the air filter on the 
slide carburetor, to the tip on the dyno-tuned exhaust system - has 
been carefully engineered to provide maximum power over the 
broadest rpm range.

We know you’re excited about getting your new Slayer Pro 4x4 
on the road, but it’s very important that you take some time to 
read through the Owner’s Manual. This manual contains all the 
necessary set-up, break-in, tuning, and operating procedures that 
allow you to unlock the incredible performance and adjustment 
potential that Traxxas engineers designed into Slayer Pro 4x4. 

Even if you are an experienced R/C enthusiast, it’s important 
to read and follow the procedures in this manual. Slayer Pro 
4x4 contains new technologies in the engine, suspension, and 
transmission operation that you may not be familiar with. Pay 
particular attention to the fuel and break-in requirements for 
the engine. 

The advanced design of the TRX 3.3 Racing Engine 

has a special break-in procedure that has been developed and 
proven to produce the best-performing engine possible. Using 
traditional or old-fashioned procedures could reduce engine 
performance and longevity.

Slayer Pro 4x4 is made to be a complete package that starts 
with the highest level of engineering; a professionally produced 
DVD to acquaint you with the starting, racing, and maintenance 
procedures; and is equipped stock with the most powerful Ready-
To-Race

®

 engine available. We want you to feel confident that you 

own the best-performing truck in the market and that it is backed 
by a team of professionals who aim to provide the highest level of 
factory support possible. Slayer Pro 4x4 is about experiencing total 
performance and satisfaction, not just with your truck, but also with 
the company that stands behind it. 

Thank you again for going with Traxxas. We work hard every day to 
assure you the highest level of customer satisfaction possible. We 
truly want you to enjoy your new Slayer Pro 4x4! 

3

4

5

6

7

8

14

28

29

34

36

BEFORE YOU PROCEED

SAFETY PRECAUTIONS

TOOLS, SUPPLIES, AND 
REQUIRED EQUIPMENT

ANATOMY OF THE 
SLAYER PRO 4X4

QUICK START:  
GETTING UP TO SPEED

TRAXXAS TQ 
RADIO SYSTEM

THE TRX 3.3 
RACING ENGINE

DRIVING YOUR  
SLAYER PRO 4X4

BASIC TUNING 
ADJUSTMENTS

MAINTAINING AND 
STORING YOUR 
SLAYER PRO 4X4

ADVANCED TUNING 
ADJUSTMENTS

Traxxas Support

Traxxas support is with you every step of the 
way. Refer to the next page to find out how to 
contact us and what your support options are.

Quick Start

This manual is designed with a Quick 
Start path that outlines the necessary 
procedures to get your model up 
and running in the shortest time possible. If you are an 
experienced R/C enthusiast you will find it helpful and fast. 
Be sure and read through the rest of the manual to learn 
about important safety, maintenance, and adjustment 
procedures. Turn to page 7 to begin.  

Содержание Slayer Pro 4x4 59074









































Отзывы: