background image

SLASH 4x4 • 17

VXL-3s Specifications

Input voltage:

  

4.8-11.1V (4 to 9 cells  
NiMH or 2S to 3S LiPo)

Supported Motors: 

Brushless

Motor limit: 

None

Continuous current: 

200A

Peak current : 

320A

BEC voltage:

 

6.0V DC

Transistor type:

 

MOSFET

Battery connector:

 

Traxxas High-Current 
Connector

Motor connectors: 

TRX 3.5mm bullet 
connectors

Motor/Battery Wiring:

12-gauge Maxx

®

 Cable

Thermal Protection:

2-stage thermal shutdown

 

ADJUSTING THE ELECTRONIC SPEED CONTROL

VXL-3s Battery Settings (Low-Voltage Detection Setting)

The Velineon VXL-3s electronic speed control is equipped with built-in Low-Voltage 
Detection. The Low-Voltage Detection circuitry constantly monitors the battery 
voltage. When the battery voltage begins to reach the minimum recommended 
discharge voltage threshold for LiPo battery packs, the VXL-3s will limit the power 
output to 50% throttle. When the battery voltage attempts to fall below the 
minimum threshold, the VXL-3s will shut down all motor output. The LED on the 
speed control will slowly blink red, indicating a low-voltage shutdown. The VXL-3s 
will stay in this mode until a fully charged battery is connected. 
The VXL-3s speed control’s Low-Voltage Detection has been set up for best 
performance with the batteries supplied with your model. If factory-equipped with 
NiMH batteries, the speed control’s LED will glow red when it is turned on, indicating 
Low-Voltage Detection is disabled. If factory-equipped with LiPo batteries, the LED 
will glow green when it is turned on, indicating Low-Voltage Detection is activated. 

Never use LiPo batteries while Low-Voltage Detection is disabled. 

To verify the Low-Voltage Detection setting:

1.  Turn on the transmitter (with the throttle at neutral).
2.  Connect a fully charged battery pack to the VXL-3s. 
3.  Press and release the EZ-Set button to turn the VXL-3s on. If the LED is solid red, 

then the Low-Voltage Detection is DISABLED (not safe to use LiPo batteries). If 
the LED is solid green, then Low-Voltage Detection is ACTIVATED.

To activate Low-Voltage Detection (LiPo setting):

1.  Make sure the LED on the VXL-3s is on and red. 
2.  Press and hold the EZ-Set button for ten seconds. The 

LED will turn off and then light green. Also, a “rising” 
musical tone will be emitted from the motor.

3.  Low-Voltage Detection is now ACTIVATED.

To disable Low-Voltage Detection (NiMH setting):

1.  Make sure the LED on the VXL-3s is on and green. 
2.  Press and hold the EZ-Set button for ten seconds. The 

LED will turn off and then light red. Also, a “falling” 
musical tone will be emitted from the motor.

3.  Low-Voltage Detection is now DISABLED.  

Transmitter Adjustments for the VXL-3s ESC

Before attempting to program your VXL-3s ESC, it is important to make sure that 
your transmitter is properly adjusted (set back to the factory defaults). Otherwise, 
you may not get the best performance from your speed control.

The transmitter should be adjusted as follows:

If the transmitter settings have been adjusted, reset them to the factory defaults. 
1.  Turn the transmitter off.
2.  Hold both MENU and SET.
3.  Turn the transmitter on.
4.  Release MENU and SET. The transmitter LED will blink red.

5. Press SET to clear settings. The LED will turn solid green and the transmitter is 

restored to default.

VXL-3s Setup Programming (Calibrating your ESC and transmitter)

Read through all of the programming steps before you begin. If 
you get lost during programming or receive unexpected results, 
simply unplug the battery, wait a few seconds, plug the battery 
back in, and start over.  
1. Connect a fully charged battery pack to the VXL-3s. 
2. Turn on the transmitter (with the throttle at neutral).
3. Press and hold the EZ-Set button (A). The LED will first 

turn green and then red. Release the EZ-Set button. 

4. When the LED blinks RED ONCE, pull the throttle trigger 

to the full throttle position and hold it there (B).

5. When the LED blinks RED TWICE, push the throttle 

trigger to the full reverse and hold it there (C).

6. When the LED blinks GREEN ONCE, programming is 

complete. The LED will then shine green or red (depending on 
Low-Voltage Detection setting), indicating the VXL-3s is on and 
at neutral (D).

VXL-3s Operation

To operate the speed control and test programming, place the vehicle on a stable 
block or stand so that all of the drive wheels are off the ground. Disconnect motor 
wires “A” and “C” (see page 11), this will ensure the motor does not drive the wheels 
during testing. Do not test programming without disconnecting the motor wires. 
Note that in steps 1-7 below, Low-Voltage Detection is DISABLED (factory default) 
and the LED shines red. If Low-Voltage Detection is ACTIVATED, the LED will shine 
green instead of red in steps 1-7 below. 

Never use LiPo batteries while Low-Voltage 

Detection is disabled. 

1. With the transmitter on, press and release the EZ-Set button. The LED will shine 

red. This turns the VXL-3s on. 

2. Apply forward throttle. The LED will turn off until full throttle power is reached. 

At full throttle, the LED will illuminate red.

3. Move the trigger forward to apply the brakes. Note that braking control is fully 

proportional. The LED will turn off until full braking power is reached. At full 
brakes, the LED will illuminate red.

4. Return the throttle trigger to neutral. The LED will shine red.
5. Move the throttle trigger forward again to engage reverse (Profile #1).  

The LED will turn off. Once full reverse power is reached, the LED  
will illuminate red. 

6. To stop, return the throttle trigger to neutral. Note that there is a programmed 

delay when changing from reverse to forward. This prevents damage to the 
transmission on high-traction surfaces.

7. To turn the VXL-3s off, press the EZ-Set button until the LED turns  

off (.5 seconds). 

Green then Red

A

Once Green

D

Once Red

B

Twice Red

C

Содержание Slash4x4 68086-1



































Отзывы: