Traxxas Slash VXL 58076-3 Скачать руководство пользователя страница 22

Страница: 22 / 34

22 • SLASH VXL

ADJUSTING YOUR MODEL

Once you become familiar with driving your model, you might
need to make adjustments for better driving performance.

Adjusting the Toe-in

Geometry and alignment
specs play an important role
in your model’s handling.
Take the time to set them
correctly. Turn off TSM
(see page 16); then, set the
steering trim on your transmitter to neutral. Now, adjust your servo and
tie rods so that both wheels are pointing straight ahead and are parallel
to each other (0° toe-in). This will ensure the same amount of steering in
both directions. For increased stability, add one- to two-degrees of toe
in to each front wheel. Use the turnbuckles to adjust the alignment.

Adjusting the Camber

The camber angle of both
the front and rear wheels can
be adjusted with the camber
rods (upper turnbuckles).
Use a square or right-angle
triangle to set the camber
accurately. The stock
camber of the front wheels is
-1 degree of camber. In the
rear, the stock camber is -1.5
degrees. These adjustments
should be set with the truck
positioned at its normal ride
height with a battery installed.

Fine Tuning the Shocks

The four shocks on the model greatly influence its handling.
Whenever you rebuild your shocks or make any changes to the
pistons, springs, or oil, always make changes to them in pairs (front
or rear). Piston selection depends on the range of oil viscosities
that you have available. For example, using a two-hole piston with
a lightweight oil will, at one point, give you the same damping
as a three-hole piston with heavier oil. We recommend using the
two-hole pistons with a range of oil viscosities from 10W to 50W
(available from your hobby shop). The thinner viscosity oils (30W
or less) flow more smoothly and are more consistent, while thicker
oils provide more damping. Use only 100% pure silicone shock oil

to prolong seal life. The model’s ride height
can be adjusted by adding or removing the
clip-on, spring preload spacers. Adjust the
ride height so that the suspension arms are
slightly above being parallel to the ground.
Observe how the model handles in turns.
Proper setup will add stability and help
prevent spin outs. Experiment with different
springs and shock oils to find what works
best for your current track conditions.

Shock Mounting Positions

Big bumps and rough terrain require a
softer suspension with the maximum
possible suspension travel and ride height.
Racing on a prepared track or on-road use
requires a lower ride height and firmer, more
progressive suspension settings. The more
progressive suspension settings help reduce body roll (increased roll
stiffness), dive during braking, and squat during acceleration.

Your model’s suspension can be altered to perform well in a variety
of terrain conditions. By making simple changes to the shock
positions, you can alter the handling of the vehicle.

For off-road driving:
1. Place the front shocks in the

inner hole (position 1) on the
suspension arms.

2. Place the rear shocks in position 2

on the suspension arms.

For on-road/hard-packed surface driving:
1. Place the front shocks in the

outer hole (position 2) on the
suspension arms.

2. Place the rear shocks in the

middle position (position 3)
on the suspension arms.

These settings are suggested starting
points. Experiment with the shock
positions to find the best setup for your
terrain, traction level, and driving style.

Preload

Spacer

-1.5

-1

Rear Camber

-1.5

-1

Front Camber

-1.5

-1

Toe-in

Front

Rear

2 3 4 5

All of the toe links are installed
on the truck so the left-hand
thread indicators point to the
same direction. This makes it
easier to remember which way
to turn the wrench to increase
or decrease toe link length
(the direction is the same at
all four corners). Note that the
groove in the hex indicates
the side of the toe link with
the left-hand threads.