background image

POWER MODULE INSTALLATION

Remove the 8028 LED lights power supply from the chassis (if installed). Install the 

Power Module mount on the chassis with the included 2.5x10mm countersunk 

cap screw; then, install the Lighting Power Module on the mount with the 

included 2.5x12mm (1) and 2.5x18mm (1) cap screws (Fig.1).

COMMUNICATION CABLES

 

Your Pro Scale Advanced Lighting Control System 

includes two communication cables: the 

Receiver 

Communication Cable

 and the optional 

MAXX® Link 

Cable

. You can use the Receiver Communication 

Cable with any TRX-4 or TRX-6 model. The MAXX 

Link Cable is designed for use only with TRX-4 or 

TRX-6 models equipped with the TQi receiver. 

The 

6511 Traxxas Link Wireless Module (sold separately) 

is required for Traxxas Link App functionality. Some 

models may require a software update for the TQi 

receiver via the Traxxas Link App for custom lighting 

controls and configurations

Only use one of the communication cables 

to connect the Lighting Power Module to the 

receiver. Do not use both cables together.

MAXX

®

 Link Cable

3.  Remove the receiver box cover by removing the three 3x8mm button-head cap screws (Fig 5).
4.  Remove the wire clamp by removing the two 2.5x8mm cap screws (Fig 5).
5.  Feed the loose end of the Receiver Communication Cable connector over the wire guide and into 

the receiver box. To make installation easier, unplug and remove a few of the existing wires from 

the receiver box. 

Note the locations of any unplugged wires.

 Use needle nose pliers to help 

grab the connectors and pull them through. Arrange all wires neatly between the wire guides in 

the receiver box (Fig. 6). The excess wire will be bundled inside the receiver box. 

6.  Apply a bead of the included silicone grease 

to the wire clamp (Fig. 7).  

7.  Reinstall the wire clamp and tighten the two 

2.5x8mm cap screws securely (Fig. 8).

8.  Unplug the electronic speed control (ESC) 

from the receiver (channel 2). 

9.  Plug the communication cable into the 

receiver (Fig. 9): the black connector with 

the single blue wire plugs into one of the 

channel 1 ports; the female black connector 

with the 3 black wires plugs into the channel 

2 port. Now, plug the black male connector 

(white, red, black servo cable) from the ESC 

into the black female connector (white, red, 

black servo cable) on the communication 

cable

 (refer to the Wiring Diagram for more 

detail). 

Leave the steering servo cable 

plugged into the other channel 1 port.

10. Make sure the blue o-ring gasket is properly 

seated in the groove in the receiver box so 

that the cover will not pinch it or damage it 

in any way.

11. Reinstall the cover on the receiver box and tighten the three 3x8mm  

button-head cap screws securely. Inspect the cover to make sure that the 

O-ring seal is not visible.

12. Use the supplied zip ties to bundle the wires neatly and attach them to 

the vehicle as needed so that loose wires will not become entangled with 

moving parts.

2.5x18mm CS

2.5x10mm CCS

Power Module Mount

2.5x12mm BCS

3x8mm BCS

3x8mm BCS

Receiver Box Cover

2.5x8mm CS

Wire Clamp

Fig. 1

Fig. 7

Fig. 8

TQ Receiver

Receiver Communication 

Cable Black wires to CH2

Receiver Communication 

Cable Blue wire to CH1

Servo wire to CH1

to ESC

Fig. 9

Fig. 3

Fig. 3

Receiver 

Receiver 

Communication Cable

Communication Cable

Wire Guide

Wire Guide

Fig. 6

Fig. 6

Fig. 4

Fig. 4

Battery Tray

3x10mm CCS

(hidden by battery hold down)

Receiver Communication 

Cable

MOTOR SENSE WIRING HARNESS INSTALLATION

1.  Unplug the red and black motor wires (bullet connectors) from 

the ESC. Plug the bullet connectors from the motor and the 

ESC into the motor sense wiring harness (red to red and black 

to black) (Fig. 10). Plug the harness connector into the 

Motor 

Sensor

 port on the power module 

(refer to the Wiring Diagram 

for more detail)

.

2.  Use the supplied zip ties to bundle the wires neatly and attach 

them to the vehicle as needed so that loose wires will not 

become entangled with moving parts.

3.  Plug the breakaway cable from the distribution block into the 

connector on top of the Power Module before installing the 

vehicle body (Fig. 11). 

Motor Sense Connectors

Fig. 10

Fig. 10

Breakaway Cable from 

Distribution Block

Fig. 11

Fig. 11

1.  Plug one end of the Receiver Communication Cable  

(Fig. 2) into the 

RX IN

 port on the Power Module (Fig. 3) 

(refer to the Wiring Diagram for more detail)

.

2.  Remove the 3x10mm counter-sunk cap screws (2) from 

the battery tray (Fig. 4). Lift up the battery tray and route 

the Receiver Communication Cable from the Power 

Module under the battery tray and to the receiver box 

(refer to the Wiring Diagram for more detail)

. Use a zip tie 

(included) to attach the wires. Reinstall and tighten the 

battery tray screws. 

Note:

 

Be careful not to pinch or 

damage any of the wires under the battery tray.

RECEIVER COMMUNICATION CABLE INSTALLATION

Fig. 2

Fig. 5

Содержание PRO SCALE 6591

Страница 1: ...tional included MAXX Link cable for models equipped with a TQi radio system The LDB mounts in the body of the vehicle and is the distribution hub for all the various wired lights in the body Its main function is to direct power and instructions to each of the installed lights to operate features such as brake lights tail lights reverse lights turn signals and high low beam lighting There is only o...

Страница 2: ...ounted on bumpers please visit the Support page on Traxxas com For more information about connecting additional chassis mounted accessories such as light bars mounted on bumpers please visit the Support page on Traxxas com Rock Light Rock Light Rock Light Rock Light Rock Light Rock Light Rock Light Rock Light From ESC Optional MAXX Link Cable Wiring TQi Receiver Only Breakaway Cable from Distribut...

Страница 3: ...cable refer to the Wiring Diagram for more detail Leave the steering servo cable plugged into the other channel 1 port 10 Make sure the blue o ring gasket is properly seated in the groove in the receiver box so that the cover will not pinch it or damage it in any way 11 Reinstall the cover on the receiver box and tighten the three 3x8mm button head cap screws securely Inspect the cover to make sur...

Страница 4: ...ress and release the Signal button two times again quickly Both left turn signal LEDs will blink twice and then both right turn signals LEDs will blink twice to indicate that the turn signals are activated Turn Signal Operation With the vehicle stopped turn the steering wheel on the transmitter left or right to turn on the LEDs The turn signal LEDs will continue to flash while the steering wheel i...

Отзывы: