Traxxas BLAST 38104-5 Скачать руководство пользователя страница 6

6 • TRAXXAS

Adjusting the Outdrive Shaft End Play

There should be a slight amount 
of shaft end play in the outdrive 
housing. To adjust the end play, 
loosen the set screw on the U-joint 
yoke (see image). Pull the propeller 
shaft until there is no more than 
1mm of distance at “arrow 2” in the 
drawing. Retighten the set screw.  

Boat Retrieval

If the Blast accidentally flips over and fills with water, it is equipped 
with foam flotation to help prevent it from sinking. Traxxas does not 
recommend ever trying to swim or wade to retrieve a boat. If you 
have chosen your launch site carefully (downwind), the Blast will 
probably drift back to you on its own. 
If there is no wind, you will need a tennis ball and a length of string. 
Tie the tennis ball securely to one end of the string; then, throw the 
ball over the drifting boat. Pull the ball in and try to entangle the boat 
in the string. Pull the boat back slowly to shore. If only the bow of the 
boat remains visible, try using a fishing lure with many hooks and a 
fishing pole. Try to snag the lip of the upper deck or drive mechanism 
with the hooks.

Maintenance

• Keep the Blast clean of accumulated dirt and oil. 
• Re-oil the motor bushings before each day of running. Use an oil 

made for electric motors such as 3-in-1 Oil™. 

• Periodically re-oil the bushing in the outdrive housing and the 

driveshaft tube. The oil hole for the driveshaft tube is located 
underneath the sealed receiver box.

Storage

Drain all water out of the Blast and thoroughly dry it before storage. 
Store the Blast with the hatch cover removed so that any remaining 
moisture can to evaporate.

Painting the Hull

If you wish to paint your hull some other color besides the factory 
white, choose your paint with caution. Only use paint made for 
plastic models (available from your hobby dealer). Test the paint on 
an inconspicuous and non-critical area before painting the entire 
boat. The paint on the bottom must be smooth to prevent a loss of 
performance.

Battery iD

Your model’s included battery pack is equipped with Traxxas Battery 
iD. This exclusive feature allows Traxxas battery chargers (sold 
separately) to automatically recognize connected battery packs and 
optimize the charge settings for the battery. This eliminates the need 
to fumble with charger settings and menus for the easiest and safest 
charging solution possible. Visit Traxxas.com to learn more about this 
feature and available Traxxas chargers and batteries.

Loosen

Arrow 2

Содержание BLAST 38104-5









Отзывы: