manualshive.com logo in svg

Traxxas 18 Kyle Busch, Руководство пользователя, Страница: 24 / 32

Поделиться
Скачать
Traxxas 18 Kyle Busch Скачать руководство пользователя страница 24

24 • TRAXXAS RALLY

MOTOR AND GEARING

Extensive testing has been done to determine the best gear ratio 
for your model. The stock gearing balances power, speed, and 
efficiency to optimize the performance of the model. However, 
you may wish to try different gear ratios in order to customize the 
performance of your model. The gearing chart on this page shows 
appropriate gearing for the model. 

 
By installing a pinion with fewer teeth, or a spur gear with 
more teeth, the transmission’s final drive ratio is increased. 
This means greater rpm is required to achieve a given speed. 
Using a numerically higher gear ratio will increase torque, but 
reduce top speed. Installing a pinion with more teeth, or a spur 
gear with fewer teeth, will decrease the final drive ratio, which 
will generally increase top speed but reduce torque. However, 
installing too large a pinion will “overgear” the car, which will 
reduce performance and may overheat the motor and speed 
control. Use the following formula to calculate the overall ratio for 
combinations not listed on the gear chart:

Motor Installation

To access the motor, 
remove the gear 
cover by removing 
the single screw on 
the top of the gear 
cover. The motor 
uses an aluminum 
mount for quick, 
easy motor access and gearing adjustment. 
To remove the motor, first open the right 
battery door and slide out the ESC. Next, 
remove the single large hex screw using the 
supplied 2.5mm wrench.  Then rotate the 
motor and mount to the side of the model, 
and slide backward off the post.

The motor mount is carefully engineered 
to provide additional features and 
adjustability.  Two sets of holes are 

provided for use with brushed and brushless motors.  The holes for 
brushed motors are spaced 16mm apart and accept 2.5mm screws. 
The holes for brushless motors are spaced 19mm apart and accept 
3mm screws.

Pinion Gear Installation Instructions

1.  Remove the motor as described  

previously in 

Motor Installation

. 

2.  Use a1.5mm wrench to loosen the 

pinion’s set screw. Remove the pinion. 

3.  Place the replacement pinion gear onto 

the motor shaft. Align the set screw 
hole with the flat side of the shaft. 

4.  Thread a 1.5mm set screw into the 

pinion gear but do not tighten it yet. 

5.  Slide the pinion gear down the motor shaft so the wrench shaft 

fits into the notch in the motor mount, as shown. Tighten the 
set screw. 

Adjusting Gear Mesh

Incorrect gear mesh is the most common 
cause of stripped spur gears. Gear mesh 
should be checked and adjusted anytime 
a gear is replaced. Access the gears by 
removing the single screw on the top  
gear cover. 

To set the gear mesh, cut a narrow strip of 
notebook paper and run it into the gear 
mesh of the motor. The motor is mounted 
to an aluminum motor mount. Loosen the 
single motor mount screw with the provided 
2.5mm wrench to slide the motor mount. 
Slide the motor and pinion gear into the 
spur gear. Retighten the motor mount screw 
and then remove the strip of paper. You 
should be able to run a fresh strip of paper 
through the gears without binding them.

TUNING ADJUSTMENTS

Motor Mount 

Screw

Do Not Loosen

# Spur Gear Teeth

x 5.04 = Final Gear Ratio

# Pinion Gear Teeth

  Brushed Motors

  Brushless Motors

Motor Mount Positions

Gearing Compatibility Chart

This chart shows a full range of gear 
combinations. The gear combinations in gray 
are not suitable when using the included 
6-cell battery, speed control and motor. These 
gear combinations have been included in this 
chart as they may be used with certain other 
aftermarket equipment combinations.  

Spur Gear

Pinion Gear

45

50

55

11

-

-

25.20

12

-

-

23.10

13

-

-

21.32

14

-

-

19.80

15

-

-

18.48

16

-

15.75

17.33

17

-

14.82

16.31

18

-

14.00

15.40

19

-

13.26

14.59

20

-

12.60

13.86

21

10.80

12.00

13.20

22

10.31

11.45

12.60

23

9.86

10.96

12.05

24

9.45

10.50

11.55

25

9.07

10.08

11.09

26

8.72

9.69

10.66

27

8.40

9.33

10.27

28

8.10

9.00

9.90

29

7.82

8.69

9.56

30

7.56

8.40

9.24

31

7.32

8.13

8.94

   

Stock setup

   

High Speed Gearing

   

Acceptable range

Содержание 18 Kyle Busch

































Отзывы:

Нет отзывов