manualshive.com logo in svg

TRAXX DBM-AK49H V Series, Руководство по эксплуатации, Страница: 10 / 16

Поделиться
Скачать
TRAXX DBM-AK49H V Series Скачать руководство пользователя страница 10

DBM-AK49H

 Operations Manual  |  9

DRILL BIT INSTALLATION

To  install  a  new  core  drill  use  a  32mm  open  end 

wrench to hold the shaft from turning while attaching 

the core drill, make sure it is secure.

CHECK THE POWER SOURCE

check that the hydraulic power source develops a

bar.

2. Make sure the hydraulic power source is equipped

with a relief valve set to open at 2100–2250 psi/145–

155 bar.

3. Check that the hydraulic circuit matches the tool 

for open-center (OC) operation.

CHECK THE TOOL

1. Make certain all tool accessories are correctly in-

stalled. Failure to install tool accessories properly

can result in damage to the tool or personal injury.

2. Check the equipment for signs of oil leaks. If leaks

are observed, do not use the tool; have the equip-

ment serviced before use.

3. Check fasteners for tightness.

4. Check the tool and hydraulic system for proper op-

eration and performance.

5. If the equipment does not appear to operate prop-

erly, have it serviced before use.

CONNECT HOSES

1. Wipe all hose couplers with a clean lint-free cloth

before making connections.

2. Connect the hoses from the hydraulic power source

it last to eliminate or reduce trapped pressure for easier 

NOTE:

If  uncoupled  hoses  are  left  in  the  sun,  pressure  in-

connect. When ever possible, connect the free ends

of hoses together.

The female coupler on the drill is the inlet coupler.

4. Cycle the control valve momentarily. If the drill does

not operate, the hoses might be reversed. Verify

correct connection of the hoses before continuing.

WARNING

Before you start changing the tool bit, make 

sure that the tool is disconnected from the 

power source in order to avoid unintentional 

operation of the tool and injury.

GENERAL OPERATION

1. Open the water supply valve and adjust the water

water as the drill bit advances in the hole.

2. Turn the power source on.

 

3. Start the core drill by pulling the trigger to the on posi-

tion.

4. Slowly feed the drill into the work surface and begin drill-

ing. 

Note: when drilling by hand start the drilling at an 

angle so only a small portion of the bit is contacting 

the surface, then gradually bring the drill up straight 

where the whole diameter is contacting the material.

material and turn off the core drill.

6. Turn off the power source and water supply.

When drilling into a structure that might contain

electrical wiring, be sure to know the location of the

wiring and avoid drilling into it. The housing can 

carry electrical current from live electrical wires 

into which the drill is accidentally drilled resulting in 

injury or death.

WARNING

DRILLING A HOLE

OPERATION

Содержание DBM-AK49H V Series

















Отзывы:

Нет отзывов