Traxon ProPoint Vista 200W RGBW Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 29

background image

www.traxontechnologies.com

©2020 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Installation Guide

IG0108EN V0.1 08/20

P. 13 of 29

Surface Mount Installation Steps

•

After placing the stainless steel mounting bracket on the mounting surface, mark the positions of 4 mounting

holes and drill 4 x M12 expanding anchors into the holes with the electric drill.

FIG.9: Surface Mounting Step 1

101.6mm (4")

304.8mm (12")

763.6mm (30.1")
506.4mm (19.9")

101.6mm (4")

100.8mm (4")

(Screws are not included)

Bracket Installation

•

Mark the positions of mounting holes and drill M12 expanding anchors into the holes with the electric drill. Fix

the M12*50 Outer hexagon bolt/

φ

12 flat washer/

φ

12 Spring washer as the following picture shows to install the

bracket.

NOTICE

It is the responsibility of the installer to ensure that the mechanical fixings are
appropriate for the task and if necessary, approved by a structural engineer as the
installation scenario is unique for each luminaire

FIG.10: Bracket Mounting

«
...
11
12
13
14
15
...
»

Содержание ProPoint Vista 200W RGBW






























Отзывы:

Нет отзывов

Похожие инструкции для ProPoint Vista 200W RGBW

Бренд: Quincy lab Страницы: 4

Бренд: Vahle Страницы: 96

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: Samson Страницы: 2

Бренд: L-Acoustics Страницы: 5

Бренд: YOKOGAWA Страницы: 75

AirForm Night Splint

Бренд: Össur Страницы: 16

Бренд: Össur Страницы: 17

Бренд: Aveo Engineering Страницы: 16

Бренд: Woodward Страницы: 62

Бренд: Major tech Страницы: 12

Бренд: Ekinex Страницы: 37

Бренд: HMS Страницы: 36

Бренд: Gardol Страницы: 80

Бренд: Taurus Страницы: 38

Бренд: Phonocar Страницы: 12

Бренд: Spokey Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды