Travis Industries Lopi Revere ND Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 36

background image

24

Maintaining Your Appliance

© Travis Industries

100-01165

4110919

Door Parts

ID #

Description

Qty

Part #

ID #

Description

Qty

Part #

1

Door Shell - Black
Door Shell - Brass
Door Shell - Pewter

1 230-00570

230-00572
230-00568

2

Glass (15-3/8" x 8-7/8")

1

173-01002

3

Glass Gasket

1

224-11086

4

Door Retainer (w gasket)

1

224-23020

5 Gasket

Cement

1 99900409

6 Door

Gasket

1 99900407

7

Door Handle Asbly - Black
Door Handle Asbly - Brass
Door Handle Asbly - Pewter

1 224-14042

99900410
224-14052

8

Spring - Black
Spring - Brass
Spring - Pewter

1 100-14122

99300100
100-04103

9 Washers

2 100-03501

10 Cam

1 99900417

11 Nut,

Brass

1 101-00007

12

Glass Clips - Top
Glass Clip - Bottom

2
1

224-230022
224-230021

13

#8-32 3/8" Type F Screw

8

225-20039

14 Set

Screw

2 225-20038

Replacing the Glass

The glass must not contact the door retainer or glass clips directly. The glass gasket and glass clip
gaskets insulate the glass to prevent cracking. Do not over-tighten the glass clips.

See "Door Shell Installation" (pg. 29) for details on removing the door handle and shell. NOTE: The glass
gasket is placed in the grove along the inside perimeter of the door retainer. Make sure the glass clip
screws are all fully tightened - they must be flush with the door retainer for the door shell to install.

Replacing the Door Gasket

The door gasket inserts into the outer groove of the door retainer. Insert gasket cement holds it in place.
Before installing, remove any residual cement. Lay the gasket in place (start at the lower left corner) and
cut off any excess gasket (do not stretch the gasket. The cement fully cures with heat from the Insert.
You may need to open and close the door repeatedly to get the gasket to seat fully.

Replacing the Door Handle

See the illustration above for a component list (see pg. 22 for details on adjusting the door).

9/16" Wrench

5

10

8

9

12

7

6

3

4

1

2

11

NOTE: Place the glass gasket around the
perimeter of the door retainer.

NOTE: Glue the door gasket
to the door retainer.

# 20 Torx Driver

13

14

1/8” Hex Wrench

«
...
22
23
24
25
26
...
»

Содержание Lopi Revere ND





































Отзывы:

Нет отзывов

Похожие инструкции для Lopi Revere ND

Бренд: Jetmaster Страницы: 13

Grandville GVF36-2P

Бренд: Napoleon Страницы: 28

Бренд: JC BORDELET Страницы: 22

Бренд: Target Страницы: 30

Бренд: KAL-FIRE Страницы: 72

DRT4000-C Series

Бренд: Superior Fireplaces Страницы: 80

Бренд: Camina & Schmid Страницы: 40

Бренд: True North Страницы: 28

Бренд: DutchWest Страницы: 36

COALFLAME BR627

Бренд: Valor Страницы: 11

BATHYSCAFOCUS Hublot

Бренд: Focus Страницы: 14

Бренд: Focus Страницы: 20

Бренд: FocalPoint Страницы: 4

F820590 FPFBQ392

Бренд: FocalPoint Страницы: 4

Бренд: FocalPoint Страницы: 7

PANORAMIC COMPLETE ELECTRIC SUITE

Бренд: Focal Point Страницы: 8

LJSF4009E-EHS88

Бренд: Focal Point Страницы: 10

Бренд: Focal Point Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды