Travis Industries AGP Pellet Insert Скачать руководство пользователя страница 1

Страница: 1 / 52

AGP Pellet Insert

•

Masonry Fireplace

• Factory-Built

(Metal)Fireplace

• Mobile Home Approved

-- Please read this entire manual before

installation and use of this pellet fuel-
burning room heater. Failure to follow
these instructions could result in
property damage, bodily injury, or even
death.

-- Contact local building or fire officials

about restrictions and installation
inspection requirements in your area.

-- Save these instructions.

Tested and Listed by:

ASTM E1509-4 ULC-S628

Installer

: After installation give this manual to the home-

owner and explain operation of this insert.

Consumer

: Retain this manual for future reference.

$10.00



Part # 100-01341

4141230

Travis Industries, Inc.

www.travisproducts.com

12521 Harbour Reach Drive

Mukilteo, WA 98275

Содержание AGP Pellet Insert





















































Результаты поиска

Содержание AGP Pellet Insert

Отзывы:

Бренды по названию

Популярные бренды

Travis Industries AGP Pellet Insert, Руководство по установке

Результаты поиска

Содержание AGP Pellet Insert

Отзывы:

Бренды по названию

Популярные бренды