Travis Industries 31 DVI GSB2 Скачать руководство пользователя страница 9

 

Installation  (for qualified installers only) 

© Travis Industries 

4140813 

100-01296 

Factory-Built (Metal) Wood-Burning Fireplace Requirements 

NOTE

:  Any parts that are removed must be removed in a way that would allow them to be re-

installed if the insert is ever removed (removal of rivets or screws is acceptable). 

The damper ("A") and grate (with log set) ("B") must be removed (see the illustration below) 

The smoke shelf ("C"), internal baffles ("D"), screen ("E"), masonry lining or refractory ("G" & "I"), and 
metal or glass doors ("F") may be removed (if applicable) 

The fireplace must be permanently marked to 
indicate that it has been altered and is no longer 
suitable for burning solid fuel (wood), unless the 
removed parts are re-installed.  Cutting of any 
metal or glass parts is prohibited. 

The insulation ("H"), and any structured rigid frame 
members must not be removed or altered (side and 
top of door frame, side and top of the face of the 
fireplace, metal sides, etc.). 

The metal floor ("J") may be removed to allow 
additional room for installation of the insert.  If the 
floor is removed the insert must be placed directly 
on the metal base of the metal fireplace. 

The surround panels should not seal ventilation 
openings on the fireplace.

 

 

If the factory-built fireplace has no gas access hole(s) provided, an access hole of 1.5 inch (37.5 mm) 
or less may be drilled through the lower sides or bottom of the firebox in a proper workmanship like 
manner.  This access hole must be plugged with non-combustible insulation after the gas supply line 
has been installed. 

Fireplace Altered Tag 

Attach the "This fireplace has been altered..." plate to the fireplace (use two screws or other suitable 
method).  You may wish to place it in a location where it will be covered by the surround panels. 

 

Hearth Requirements 

The heater and face must not contact combustible surfaces.  A non-combustible hearth extension is 
not required.  However, if the heater is installed next to the floor, we recommend a hearth to protect 
the flooring surface from discoloration or other negative impact from the heater. 

C

B

F

I

D

E

A

G

H

J

Содержание 31 DVI GSB2







































Отзывы: