TransLite TL-9916 Скачать руководство пользователя страница 25

Страница: 25 / 26

P a g e

Prevention Measure

➢

Installing the device at the place in which environment temperature between 0 to 45 °C

➢

Making sure good ventilation for the heat-sink on the rear panel and other heat-sink

bores if necessary

➢

Checking the input AC within the power supply working range and the connection is

correct before switching on device

➢

Checking the RF output level varies within tolerant range if it is necessary

➢

Checking all signal cables have been properly connected

➢

Frequently switching on/off device is prohibited; the interval between every switching

on/off must greater than 10 seconds.

Conditions to unplug power cord

➢

Power cord or socket damaged.

➢

Any liquid flowed into device.

➢

Any stuff causes circuit short

➢

Device in damp environment

➢

Device was suffered from physical damage

➢

Longtime idle.

➢

After switching on and restoring to factory setting, device still cannot work properly.

➢

Maintenance needed

CHAPTER 5

PACKING LIST

TL-9916 16 in 1 IP QAM Modulator

1PC

User's Manual

1PC

Power Cord

1PC

Содержание TL-9916



























Результаты поиска

Содержание TL-9916

Отзывы:

Бренды по названию

Популярные бренды

TransLite TL-9916, Руководство пользователя

Результаты поиска

Содержание TL-9916

Отзывы:

Бренды по названию

Популярные бренды