Transition Networks Stand-Alone Media Converter S4TEF10xx-11x Скачать руководство пользователя страница 9

16

S4TEF10xx-11x

24-hour Technical Support: 1-800-260-1312  International: 00-1-952-941-7600

Operation -- Continued

To show the configuration menu for the remote device:

1.

At the prompt, type the letter “C,” press the spacebar, then type the letter “R.”

2.

Press the ENTER key and the remote device configuration menu will appear: 

Note:

In this menu, the T1/E1/J1 commands for remote loopback, for example,
type the command this way:  

LL, press the spacebar, then

type the port number, press spacebar, then type

the number of the command,

in this case

(1= enable or 2 =

disable)

The command sequence Is Not case sensitive.

Remote Device Configuration Menu:

*T1/E1/J1:

LL x 1 - Local Loopback on T1/E1/J1 Port x ENABLE

LL x 2 - Local Loopback on T1/E1/J1 Port x DISABLE

RL x 1 - Remote Loopback on T1/E1/J1 Port x ENABLE

RL x 2 - Remote Loopback on T1/E1/J1 Port x DISABLE

XE x   - Enable Transmit AIS on LOS for Port x

XD x   - Disable Transmit AIS on LOS for Port x

EB x   - Encoding set to B8ZS on Port x

EA x   - Encoding set to AMI on Port x

*RS-232:

B x    - Serial port baud rate (1=9600, 2=19200, 3=36400,
4=57600)

*Enet 10/100:

A1     - Autonegotiation ENABLE

A2     - Autonegotiation DISABLE

TLPT1  - Transparent Link Pass Through ENABLE

TLPT2  - Transparent Link Pass Through DISABLE

F10    - Force 10Mbps

F100   - Force 100Mbps

FF     - Force Full Duplex

FH     - Force Half Duplex

S      - Save new Configuration and Exit

Q      - Exit without saving Configuration

->

17

techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.

Operation -- continued

To update the PIC code of a remote device:

1.

At the prompt, type the letter “U.” 

2.

Press the ENTER key and the code will start to transfer. On the screen, the
incrementing percent line shows the percent of the transferring code:

Note:

This command will take several minutes to complete. Do Not power down
the device or break the fiber connection during this code transfer.

Fiber Load...Transferring of binary pic code to remote...

6 percent...

To enable hardware bypass mode for software control:

1.

At the prompt, type the letter “B.”

2.

Press the ENTER key and a Reset message will appear on the screen. 

3.

Type the letter “Y” to Enable H/W Bypass. 

4.

Press the ENTER key. When the Reset completes, the “login” prompt will
appear.

To disable the hardware bypass mode:

1.

At the prompt, type the letter “B”  again.

2.

Press the ENTER key and a Reset message will appear on the screen.

3.

Type the letter “Y” to Disable H/W Bypass. 

4.

Press the ENTER key. When the Reset completes, the “login” prompt will
appear as show below.

-> b

This command will cause reset. Are you SURE you wish to
reset device (y/n)?

Enable H/W Bypass...

Resetting Board!

Type 'L' to login

->

-> b

This command will cause reset. Are you SURE you wish to
reset device (y/n)?

Disable H/W Bypass...

Resetting Board!

Type 'L' to login

->

Содержание Stand-Alone Media Converter S4TEF10xx-11x
















Отзывы: