SSDTF10xx IN THE NETWORK
NOTE: THE SSDTF10xx REQUIRES A CSU BETWEEN THE MEDIA
CONVERTER AND THE PUBLIC TELEPHONE NETWORK.
NOTE: E1 MEDIA CONVERTERS MUST BE USED IN PAIRS. A TRANSITION
Networks SSDTF30xx stand-alone media converter can be used with another
SSDTF10xx stand-alone media converter, with a CSDTF10xx chassis media
converter, or with a previous model TRANSITION Networks T1/E1 media
converter, such as a C/T1E1-CF-01 or a T1E1-CF-01.
Media converter is framing independent (as ESF vs D4) and supports all
common line codes, (AMI, B8ZS, HDB3).
All Ones Insertion (AIS) on loss of signal at copper and/or fiber interface.
Switch-Selectable Functions
LOOPBACK TEST FUNCTION
A loopback switch facilitates installation and network debug procedures.
The path for the SSDTF10xx loopback is shown:
TRANSMIT ALL ONES FUNCTION
A selectable Transmit All Ones switch on the fiber interface and on the
twisted-pair interface allows for insertion of an “all ones” pattern on that
interface when
signal detect is lost, which creates an alarm condition at
the equipment connected to the interface.
INSTALLATION
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when setting switch and when installing Media Converter Slide-in-
Module in the Media Conversion Center. Failure to observe this caution could
result in damage to, and subsequent failure of, the Media Converter Slide-in-
Module.
Use small flatblade screwdriver or similar device to set recessed switches for
site installation.
Set Loopback Test Switch
NOTE: The Loopback Test switch, located on Media
Converter Slide-in-Module front panel, allows the
network administrator to enable a loopback test for
installation and network debug procedures.
TECHNICAL SPECIFICATIONS
Standards
Emissions: CISPR A
E1 Physical Layer: ITU-T, ANSI, AT&T, ETSI
Dimensions
2.9" x 4.8" x 1.4"
Weight
8 oz (approximate)
Power Source
7.5-15.9 VDC AC Adapter
Power Consumption
5 watts
Power Supply Requirements
Replace power supply with only the equivalent
input rating (see below) and output rating (regulated 9VDC at 550 mA).
TN PN
Requirement
Location
25034 or 3525
240 volts, 50 hertz
United Kingdom
25034 or 3525
230 volts, 50 hertz
Europe
3518
120 volts, 60 hertz
USA/Canada/Mexico
3514
100 volts, 50-60 hertz Japan
25034 or 3525
240 volts, 50 hertz
Australia
Environment
Typical Operating Temperature:
0°
to
50°C (32°
to
122°F )
Storage Temperature:
-20°
to
85°C (-4°
to
185°F)
Humidity
10-90%, non condensing
Altitude
0-10,000 feet
Warranty
Lifetime
SSDTF30xx
7
2
DECLARATION OF CONFORMITY
Name of Mfg:
Transition Networks
6475 City West Parkway, Minneapolis MN 55344 USA
Model:
SSDTF30xx Series Copper-to-Fiber Media Converter
Part Number:
SSDTF3011-110, SSDTF3012-110, SSDTF3013-110,
SSDTF3022-110
Regulation:
EMC Directive 89/336/EEC
Purpose: To declare that the
SSDTF30xx
to which this declaration refers is in
conformity with the following standards.
EN 55022:1994; EN 55024:1998; FCC Part 15 Class A; EN 60950 A4:1997; UL 1950
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
_January 8, 2001_____
Stephen Anderson, Vice-President of Engineering
Date
Fiber
TP
TP
Loop
