Transition
Networks
SISTP10x0
‐
3xx
‐
LRT
Quick
Start
Guide
33732
Rev.
A
https://www.tranition.com
Page
1
of
2
SISTP10x0
‐
3xx
‐
LRT
Series
Industrial
Unmanaged
PoE/PoE+
GbE
Switches
Quick
Start
Guide
The
SISTP10x0
‐
3xx
‐
LRT
series
industrial
unmanaged
GbE
switches
are
a
plug
‐
and
‐
play
Ethernet
switches
that
make
an
easy
transition
to
Gigabit
Ethernet.
The
SISTP10x0
‐
3xx
‐
LRT
series
consist
of
two
PoE+
models:
SISTP1040
‐
342
‐
LRT
and
SISTP1040
‐
382
‐
LRT.
See
the
Install
Guide
for
Safety
Warnings
and
Cautions,
Ordering
info,
features,
pecs,
front/back
panel
descriptions,
installation
and
setup,
grounding,
power
supply,
LED,
troubleshooting,
regulatory
agency,
warranty,
and
contact
information.
Front
Panel
The
SISTP1040
‐
382
‐
LRT
front
panel
is
shown
right.
RESET Button
You
can
press
the
bottom
panel
RESET
button
to
reboot
the
switch.
Installation
and
Setup
See
the
Install
Guide
for
unpacking
and
package
contents.
The
Switch
can
be
Wall
mounted
or
installed
on
a
DIN
Rail.
See
the
Install
Guide.
Mounting
the
Switch
on
a
Wall
(Optional)
1.
Attach
the
wall
mounting
plates
to
rear
panel
of
chassis.
Insert
screws
and
tighten.
2.
Install
user
‐
supplied
screws
on
the
appropriate
location
on
the
wall.
3.
Make
sure
the
switch
is
attached
securely
to
wall.
Mounting
the
Switch
on
a
DIN
Rail
1.
Attach
the
DIN
Rail
mounting
kit
to
the
rear
panel
of
the
chassis.
Insert
screws
and
tighten.
2.
Insert
the
upper
lip
of
the
DIN
rail
into
the
DIN
‐
rail
mounting
kit
and
press
switch
towards
DIN
rail
until
it
snaps
into
place.
3.
Make
sure
that
the
switch
is
attached
securely
to
DIN
Rail.
Note
:
Make
all
cable
connections
and
perform
grounding
before
connecting
to
power.
Install
and
Connect
SFPs
via
Fiber
Optic
Cable
For
SFP
ports
use
UL
Listed
Optional
Transceiver
products,
Rated
3.3Vdc,
Laser
Class
1.
1.
Prepare
a
fiber
optic
cable
with
appropriate
connecter.
Warning
:
Fiber
optic
port
is
a
Class
1
laser
device.
2.
Remove
a
rubber
plug
and
position
the
SFP
at
an
SFP
slot
with
the
label
facing
correctly.
3.
Carefully
slide
the
SFP
device
into
the
slot,
aligning
it
with
the
internal
installation
guides.
Ensure
that
the
SFP
device
is
firmly
seated
against
the
internal
mating
connector.
4.
See
the
related
SFP
manual
for
operating
information
specific
to
your
particular
SFP
model.
5.
Connect
the
other
end
of
the
cable
to
the
appropriate
far
end
Ethernet
port.
Note
:
After
the
cable
is
properly
connected
at
both
ends,
the
Switch
LEDs
should
be
functional.
