may be used. Note: Coax slide in card (E-CX-SIC) may
not be used for redundancy connection.
Shielded RJ-45 Connectors/Twisted pair wire
The 24 port hub is provided with shielded RJ-45 Modular
connectors to meet European requirements. To fully utilize
shielding capability, use AMP shielded male modular RJ-45
connectors; tying cable shield to the shielded connector.
You may use shielded or unshielded 24 or 26 AWG twisted
pair wire without loss of transmission distance. The maxi-
mum distance between the hub and a network device is 100
meters (330 feet). The use of flat cable (silver satin) patch
cables are not recommended and may affect the system’s
overall performance.
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
A
B
1
2
3
4
5
6
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
Power
1
2
3
567
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
57
9
11
13
15
17
19
21
23
2
4
68
12
14
16
18
20
22
24
10
1
2
Link
Rear Slot
Enabled
Fault
A
B
1
2
3
4
5
FIG 7: FIVE SEGMENT RULE
Model 1002 Hub Views: Figure 1
2A, 250V
Caution: For continued protection against
risk of fire, replace only with same type and
rating of fuse. 250V, 2A
SIC SLOT 1
SIC SLOT 2
USE ONLY WITH
250V FUSES
DISCONNECT POWER
BEFORE REPLACING FUSES
AUI
Power
1
2
3
5
6
7
8
4
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Unit I.D.
10BaseT Hub 1002
1
3
5
7
9 11 13 15 17 19 21 23
2
4 6
8
12 14 16 18 20 22 24
10
1
2
Link
Rear Slot
Enabled
Fault
24 PORT HUB FRONT VIEW
24 PORT HUB REAR VIEW
Reset Hub
Rear Port Configuration:
Normal AUI Operation
Redundancy Enabled
24 PORT HUB SIDE VIEW
Attention: Couper le courant avant de
replacer le fusible
Hub Reset Switch
The Hub Reset switch is used if the hub locks up or a mal-
function occurs. This switch is located on the side of the
hub.
