4
CBFTF10xx-14x
24-Hour Technical Support:
1-800-260-1312
-- International:
00-1-952-941-7600
Installation
-- Continued
Set the Dip Switches -- Continued
NOTE: Dip switch 4 (in the “SW” set) applies to fiber port 1 (F1).
4. Fiber Mode (Fiber Port 1)
UP (Full-Duplex)
- The cable distances for fiber port
1 (F1) are constrained by the cable requirements (see
pages 1 and 2).
DOWN (Half-Duplex)
- The cable distances for fiber
port 1 (F1) are constrained by the 512-Bit Rule (see
pages 9).
NOTE: Dip switch 5 (in the “SW” set) applies to
all
twisted-pair copper ports
(TP1, TP2, TP3, TP4).
5. AutoCross
UP (Enable)
- The media converter connects
automatically to either straight-through or crossover
twisted-pair copper cable.
DOWN (Disable)
- Either straight-through or
crossover twisted-pair copper cable must be
installed, according to the site requirements
NOTE: Dip switch 6 (in the “SW” set) applies to
both
fiber ports (F1, F2).
6. Fiber Redundancy
UP (Disable)
- When Fiber Redundancy is disabled,
Fiber Port 1 (F1) and Fiber Port 2 (F2) act as normal
bridging ports.
DOWN (Enable)
- When Fiber Redundancy is
enabled, Fiber Port 1 (F1) and Fiber Port 2 (F2) are
configured as either forwarding or disabled. At any
given time, one port will be disabled and one port
will be forwarding.
Redundant Fiber Disable
Redundant Fiber Enable
6
UP
DOWN
Fiber Full-Duplex
Fiber Half-Duplex
DOWN
UP
4
AutoCross Enable
AutoCross Disable
UP
5
DOWN
5
-- Click the
“Transition Now”
link for a live Web chat.
Installation
-- Continued
Set the Dip Switches -- Continued
NOTE: Dip switches 1, 2, 3, and 4 (in the Config. Switches set) apply
only
to
twisted-pair copper port 2 (TP2).
1. Twisted-Pair Auto-Negotiation
UP (Enabled)
- The media converter “advertises”
ALL rate and mode capabilities to the network:
• 100Mb/s full-duplex • 100Mb/s half-duplex,
• 10Mb/s full-duplex • 10Mb/s half-duplex.
DOWN (Disabled)
- The bridging media converter
does not “advertise” the rate and mode
capabilities to the network.
Switch 2
and
switch 3
are then used to set the twisted-pair rate and mode.
2. Twisted-Pair Rate
UP (100Base-TX)
- Sets the twisted-pair rate to
100Base-TX.
DOWN (10Base-T)
- Sets the twisted-pair rate to
10Base-T.
3. Twisted-Pair Mode
UP (Full-Duplex)
- The twisted-pair cable
distances are constrained by the cable
requirements (see pages 1 and 2).
DOWN (Half-Duplex)
- The twisted-pair cable
distances are constrained by the 512-Bit Rule (see
page 9).
4. Monitor for Twisted-Pair Port 2 (TP2)
UP (Off)
- The twisted-pair port 2 (TP2) functions
as directed by
switches 1
,
2
, and
3
.
DOWN (On)
- The twisted-pair port 2 (TP2)
functions as a “sniffer” port and transmits all
packets received from ports F1 and TP1.
Twisted-Pair Full-Duplex
Twisted-Pair Half-Duplex
UP
DOWN
3
Monitor on TP2 OFF
Monitor on TP2 ON
UP
DOWN
4
Twisted-Pair 100Base-TX
Twisted-Pair 10Base-T
UP
DOWN
2
UP
DOWN
1
Twisted-Pair Auto-Negotiation ON
Twisted-Pair Auto-Negotiation OFF
