background image

Your Trango Systems Wireless PTZ System:

C

ongratulations on choosing 

Trango Systems, Inc.

 to fulfill your wireless needs.  Unpack your system carefully.  If any items are

missing, notify your sales representative.  If an item appears to be damaged from shipment, replace it in its packing material and notify
the shipper.

Save the packaging for further storage of the equipment.

Service:
I

f the unit ever needs repair service, contact Trango Systems customer service for return authorization and shipping instructions.

Note: This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance
with these instructions, may cause harmful interference to radio communications.  However, there is no guarantee that
interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by
one of more of the following meaures:

1) Reorient the receiving antenna;
2) Increase the separation between the affected equipment and the receiver;
3) Connect the affected equipment to an outlet on a different circuit from that
     which the receiver is connected to;
4) Consult the dealer and/or experienced radio/TV technician for help.

FCC ID Numbers:

Transmitter PTZ-900TX:

FCC ID# NCYPTZ900TX

WARNING

: Intentional or unintentional changes or modifications not expressly approved by the party responsible for

compliance must not be made.  Any such modifications could void the user’s authority to operate the equipment.

Содержание PTZ-900











Отзывы: