Trane Voyager Commercial, Инструкция по установке, эксплуатации и обслуживанию

Страница: 89 / 156

RT-SVX34R-EN 89
W WA AR RN NIIN NG G
L Liiv ve e E Elle eccttrriicca all C Co om mp po on ne en nttss!!
F Fa aiillu urre e tto o ffo ollllo ow w a allll e elle eccttrriicca all ssa affe etty y p prre ecca au uttiio on nss
w wh he en n e ex xp po osse ed d tto o lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss cco ou ulld d
rre essu ulltt iin n d de ea atth h o orr sse erriio ou uss iin njju urry y..
W Wh he en n iitt iiss n ne ecce essssa arry y tto o w wo orrkk w wiitth h lliiv ve e e elle eccttrriicca all
cco om mp po on ne en nttss,, h ha av ve e a a q qu ua alliiffiie ed d lliicce en nsse ed d e elle eccttrriicciia an n
o orr o otth he err iin nd diiv viid du ua all w wh ho o h ha ass b be ee en n p prro op pe errlly y ttrra aiin ne ed d
iin n h ha an nd dlliin ng g lliiv ve e e elle eccttrriicca all cco om mp po on ne en nttss p pe errffo orrm m
tth he esse e tta asskkss..
H HIIG GH H V VO OL LT TA AG GE E IIS S P PR RE ES SE EN NT T A AT T T TE ER RM MIIN NA AL L
B BL LO OC CK K H HT TB B1 1 O OR R U UN NIIT T D DIIS SC CO ON NN NE EC CT T S SW WIIT TC CH H..
3. Remove the mist eliminator retainer bracket and the
mist eliminators from the fresh air hood.
4. Remove the five (5) screws in the top and bottom of
each fresh air damper located inside the hood area.
5. Using the Service Test guide in , p. 68 — Table 46,
p. 74 , momentarily jump across the test terminals
one time for constant volume applications, or three
consecutive times for a variable air volume
application, to start the Minimum Ventilation Test.
6. With the supply fan “On” and rotating in the proper
direction, measure the return duct static pressure.
7. Using Table 65, p. 89 , enter the desired amount of
fresh air and the return air static pressure reading to
obtain the proper damper opening dimension.
8. Loosen the adjustment screws on each side of the
damper and slide it downward to the required
opening.
9. Tighten the adjustment screws and re-install the
mist eliminators and the mist eliminator retainer
bracket.
10. Open the main power disconnect or the unit
mounted disconnect switch to shut the unit off and
to reset the RTRM.
11. Before closing the disconnect switch, ensure that
the compressor discharge service valve(s) and
suction service valve(s) are backseated.
Table 65. Damper adjustment
Damper Opening (in.)
Return Air Static Pressure - Inches w.c.
Damper #1 Damper #2
-0.20 -0.40 -0.60 -0.80 -1.00 -1.20 -1.40 -1.60
2 0 430 590 725 840 950 1040 1120 740
4 0 780 1080 1330 1545 1730 1890 2035 2170
6 0 1185 1620 1990 2300 2575 2815 3030 3240
8 0 1530 2110 2600 3025 3390 3705 3985 4240
10 0 1930 2655 3270 3800 4250 4650 5005 5345
10 2 2295 3165 3910 4545 5095 5575 6010 6415
10 4 2660 3650 4510 5255 5905 6480 6995 7470
10 6 3010 4150 5130 5965 6690 7330 7900 8440
10 8 3345 4600 5680 6610 7410 8120 8765 9365
10 10 3690 5125 6350 7395 8295 9075 9775 10420
Starting the Compressor
Optional service valves must be fully opened before
startup (suction and discharge line).
N No otte e:: Suction and discharge service valves are
standard on high efficiency units and 40-50T
standard efficiency constant volume units.
N NO OT TIIC CE E
C Co om mp prre esssso orr F Fa aiillu urre e!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on n b be ello ow w cco ou ulld d rre essu ulltt iin n
cco om mp prre esssso orr ffa aiillu urre e..
U Un niitt m mu usstt b be e p po ow we erre ed d a an nd d ccrra an nkkcca asse e h he ea atte errss
e en ne errg giizze ed d a att lle ea asstt 8 8 h ho ou urrss B BE EF FO OR RE E cco om mp prre esssso orrss
a arre e sstta arrtte ed d..
Starting 27.5 to 35 Ton Standard
Efficiency Units
Install a set of service gauges onto the suction and
discharge service ports. To start the compressor test,
close the main power disconnect switch or the unit
mounted disconnect switch.
Jump across the “Test terminals” on LTB1 or toggle
the test switch three consecutive times if it is a constant
volume application, or five times if it is a variable air
volume application for two to three seconds per jump.
Refer to
, p. 68 - Table 46, p. 74 for the Cooling Test
sequence.
S Stta arrttu up p