Trane Tracer ZN521 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 60

background image

CNT-SVX07D-EN

47

Status indicators for operation and communication

Service pin button

The Service pin button is located as shown in Figure 19 on page 43. The Service pin button is used
to:

•

Identify a device (see “Identifying a device” in the

Rover Installation/Operation/Programming

guide (EMTX-SVX01A-EN)

•

Add a device to the active group (see “Adding a device” in EMTX-SVX01A-EN)

•

Verify PCMCIA communications (see “Verifying PCMCIA communications” in EMTX-SVX01A-
EN)

•

Make the green (status) LED “wink” to verify that the controller is communicating on the link
(see Table 14 on page 47 and “Setting the Auto-wink option” in EMTX-SVX01A-EN)

Interpreting LEDs

The red (service) LED on the Tracer ZN521 controller (see Figure 19 on page 43) indicates whether
the controller is capable of operating normally (see

The green (status) LED on the Tracer ZN521 controller (see Figure 19 on page 43) indicates whether
the controller has power applied to it and if the controller is in manual test mode (see

).

Table 13. Red LED: Service indicator

LED activity

Explanation

LED is off continuously when power is applied

to the controller.

The controller is operating normally.

LED is on continuously when power is applied

to the controller.

The controller is not working properly, or

someone is pressing the Service pin button.

LED flashes once every second.

The controller is not executing the application

software because the network connections

and addressing have been removed.

1

1

Restore the controller to normal operation using the Rover service tool. Refer to EMTX-SVX01A-

EN for more information.

Table 14. Green LED: Status indicator

LED activity

Explanation

LED is on continuously.

Power is on (normal operation).

LED blinks (one recurring blink).

Manual output test mode is being performed

and no diagnostics are present.

LED blinks (blinks twice as a recurring

sequence).

Manual output test mode is being performed

and one or more diagnostics are present.

LED blinks (1/4 second on,

1/4 second off for 10 seconds).

The Auto-wink option is activated, and the

controller is communicating.

1

LED is off continuously.

Either the power is off,

the controller has malfunctioned, or

the Test button is being pressed.

1

By sending a request from the Rover service tool, you can request the controller’s green LED

to blink (“wink”), a notification that the controller received the signal and is communicating.

«
...
45
46
47
48
49
...
»

Содержание Tracer ZN521





























































Отзывы:

Нет отзывов

Похожие инструкции для Tracer ZN521

Бренд: Nelson Страницы: 19

Бренд: C-TEC Страницы: 2

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Daktronics Страницы: 5

Бренд: Daikin Страницы: 12

Бренд: OJ Electronics Страницы: 8

Бренд: OJ Electronics Страницы: 112

Бренд: OJ Страницы: 17

Slim Remote Control

Бренд: Packard Bell Страницы: 2

Бренд: Unipower Страницы: 24

Бренд: Water Specialist Страницы: 60

Бренд: YASKAWA Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды