Trane Symbio 210 Скачать руководство пользователя страница 17

Страница: 17 / 76

BAS-SVX084A-EN

Wiring Installation

Wiring Best Practices

To ensure proper network communication, follow the recommended wiring and best practices
below when installing communication wire:

•

All wiring must comply with the National Electrical Code™ (NEC) and local codes.

•

Ensure that 24 Vac power supplies are consistent in regards to grounding. Avoid sharing 24 Vac
between controllers.

•

Avoid over tightening cable ties and other forms of cable wraps. This can damage the wires
inside the cable.

•

Do not run communication cable alongside or in the same conduit as 24 Vac power. This
includes the conductors running from TRIAC-type inputs.

•

In open plenums, avoid running wire near lighting ballasts, especially those using 277 Vac.

•

Use same communication wire type, without terminators, for the zone sensor communication
stubs from the Symbio 210 controller IMC terminals to the zone sensor communication module.

•

Zone Sensor communication wiring length limits of 300 ft. (100 m).

Note:

For more details, refer to the BACnet Best Practices and Troubleshooting Guide
(BAS-SVX51-EN).

Figure 4.

BACnet MS/TP link wiring

TBT

IMC

0 1

x10

0 1

x100

ADDRESS

ACT

LINK

IMC

STATUS

Tracer

LINK 3

LINK 2

LINK 1

LINK 3

LINK 2

LINK 1

CONTR

OLLER

OUND

ADDRES

2 3 4

x10

2 3 4

x100

2/BI3

1/BI2

ACTU

VAC

OUT

VAC

XFMR

LINK

SER

VICE T

OOL

+24

VDC

IMC

STAT

SER

BI1

DAT

SET

AI1

ZONE

210

Symbio

™

CONTR

OLLER

OUND

ADDRES

2 3 4

x10

2 3 4

x100

2/BI3

1/BI2

ACTU

VAC

OUT

VAC

XFMR

LINK

SER

VICE T

OOL

+24

VDC

IMC

STAT

SER

BI1

DAT

SET

AI1

ZONE

210

Symbio

™

Symbio 210

Trane BACnet

Terminator

Symbio 210

Tracer SC+

Trane BACnet

Terminator

TBT

Содержание Symbio 210













































































Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды

Trane Symbio 210, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Symbio 210

Отзывы:

Похожие инструкции для Symbio 210

Бренды по названию

Популярные бренды