Trane RTAF-SVX001K-EN, Руководство пользователя

Страница: 51 / 102

Installation Electrical
RTAF-SVX001K-EN 51
AFD Drive Programming
Field replacement drives must be programmed via the
keypad interface. Program parameters sequentially by ID
values as defined in tables below.
Table 24. Non-compressor specific parameter settings
ID Description Setting
0-03 Region Settings [1] North American
0-20 Display Line 1.1 Small [1612] Motor Voltage
0-24 Display Line 3 Large [1617] Speed (rpm)
0-40 [Hand on] Key on LCP [0] Disabled
0-41 [Off] Key on LCP [0] Disabled
0-60 Main Menu Password 999
0-61 Access to Main Menu w/o Password [1] LCP: Read-only
1-03 Torque Characteristics [0] Compressor Torque
1-21 Motor Power [HP] See table below
(a)
1-22 Motor Voltage See table below (a)
1-23 Motor Frequency 60Hz
1-24 Motor Current See table below (a)
1-25 Motor Nominal Speed See table below (a)
1-71 Start Delay 0s
1-73 Flying Start [0] Disabled
1-78 Compressor Start Max Speed [Hz] 30Hz
1-79 Compressor Start Max Time to Trip 10s
1-82 Min Speed for Function at Stop [Hz] 10Hz
1-87 Trip Speed Low [Hz] 25Hz
3-02 Minimum Reference 30Hz
3-03
(b)
Minimum Reference See Table 26
3-41 Ramp 1 Ramp Up Time 5s
3-42 Ramp 1 Ramp Down Time 5s
3-82 Starting Ramp Up Time 3s
4-10 Motor Speed Direction [0] Clockwise
4-12 Motor Speed Low Limit [Hz] 30Hz
4-18 Current Limit 128.4%
4-19 Max Output Frequency See table below (a)
4-
14 (b)
Motor Speed High Limit [Hz] See Table 26
5-12 Terminal 27 Digital Input [2] Coast Inverse
5-13 Terminal 29 Digital Input [0] No Operation
5-40.0 Function Relay 1 [5] Running
5-40.1 Function Relay 2 [3] Drive Rdy/Rem Ctrl
5-41.0 On Delay, Relay 1 1s
5-41.1 On Delay, Relay 2 1s
5-42.0 Off Delay, Relay 1 1s
5-42.1 Off Delay, Relay 2 1s
6-10 Terminal 53 Low Voltage 2V
6-14 Terminal 53 Low Ref./Feedb. Value 30Hz
6-
15 (b)
Terminal 53 High Ref./Feedb. Value See Table 26
6-50 Terminal 42 Output
[133] Motor Cur. 4-
20mA
14-03 Overmodulation [0] Off
14-10 Mains Failure [4] Kinetic Back-up
14-11 Mains Voltage at Mains Fault See table below (a)
14-20 Reset Mode [1] Automatic Reset x 1
14-30 Current Lim Ctrl. Proportional Gain 25%
14-31 Current Lim Ctrl. Integration Time 1s
14-50 RFI Filter [0] Off
14-51 DC Link Compensation [1] On
22-75 Short Cycle Protection [1] Enabled
22-76 Interval Between Starts 60s
(a) For unit sizes 115 to 215, see Table 25 . For unit sizes 230 to 520 tons,
see Table 26 .
(b) Parameter for 230 to 520 ton units only.
Table 24. Non-compressor specific parameter settings
(continued)
ID Description Setting
Table 25. Compressor-specific parameter settings, 115 to 215 tons — 60Hz
(a)
Parameters L1 L2 M3 M4 N3
ID Description 460V 380V 575V 460V 380V 575V 460V 380V 575V 460V 380V 575V 460V 380V 575V
1-21 Motor Power (hp) 86 86 86 102 102 102 122 122 122 144 144 144 177 177 177
1-22 Motor Voltage (V) 460V 380V 575V 460V 380V 575V 460V 380V 575V 460V 380V 575V 460V 380V 575V
1-24 Motor Current (A) 91A 110A 73A 109A 132A 87A 128A 154A 101A 151A 182A 120A 183A 221A 146A
1-25
Motor Nominal
Speed (rpm)
3461 3460 3461 3459 3466 3461 3502 3505 3503 3494 3494 3494 3494 3495 3493
4-19
Max Output
Frequency (Hz)
61 61 61 61 61 61 61 61 61 61 61 61 61 61 61
14-11
Voltage at Main
Fault (V)
391V 323V 489V 391V 323V 489V 391V 323V 489V 391V 323V 489V 391V 323V 489V
(a) 400V/50 Hz units use 380V/60Hz compressor settings.