Trane PM014 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 20

Trane PM014 Скачать руководство пользователя страница 15

BAS-SVX33F-EN

15

Installing the Power Supply Module

Separating the IMC Bus for Large Systems

For large systems with heavier loads than the PM014 can power alone, the IMC bus can be
separated into sections that are sized for single power supply modules. Follow the recommended
method described below to separate the IMC bus. An alternative method is also described on

.

Note: The power supply module is not designed to supply power in parallel with other power

supplies.

Recommended method for separating the IMC bus

Note: This method preserves the power supply module warranty.

3. Perform lockout/tagout procedures for line voltage power to the cabinet.

4. Using two parallel DIN rails, position two power supply modules directly above or beneath one

another as shown in

5. Wire the two power supply modules together by using the IMC terminal blocks. Do not wire the

Vdc terminals.

Important:

To prevent power flow between modules, the Vdc terminals must not be wired.

Figure 7.

Recommended method when separating the IMC bus

PM014

PM014

24

VAC

XFMR

OUT

24

VAC

24

VAC

XFMR

OUT

24

VAC

24 Vdc
terminal

24 Vdc
terminal

«
...
13
14
15
16
17
...
»

Содержание PM014





















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды