manualshive.com logo in svg

Trane Optimus RTHD, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Trane Optimus RTHD Скачать руководство пользователя страница 25

Installation Mechanical

RTHD-SVX01K-EN

25 

•

C, D, E Family Compressors:

•

Remove (4) puck-type spacer under discharge 
side of compressor (see 

Figure 10

).

10. Remove the shipping brackets from the bottom sides 

of the oil separator(s). See 

Figure 11

.

Notes:

•

Once shipping bracket(s) is removed, the oil separator 
is only supported by the discharge line.

•

Failure to remove oil separator shipping brackets 
could result in excessive noise.

Unit Leveling

Note:

The electrical panel side of the unit is designated as 
the “front” of the unit.

1. Check unit level end-to-end by placing a level on the 

top surface of the evaporator shell.

2. If there is insufficient surface available on the top of 

evaporator shell, attach a magnetic level to bottom of 
shell to level the unit. Unit should be level to within 
1/4 inch (6.35 mm) over its length.

3. Place the level on the evaporator shell tube sheet 

support to check side-to-side (front-to-back) level. 
Adjust to within 1/4 inch (6.35 mm) of level front-to-
back.

Note:

The evaporator MUST be level for optimum heat 
transfer and unit performance.

4. Use full-length shims to level the unit.

Alternate Moving Method

If it is not possible to rig from above as shown in 

Figure 7, 

p. 22

, the unit may also be moved by jacking each end high 

enough to move an equipment dolly under each tube 
sheet support. Once securely mounted on the dollies, the 
unit may be rolled into position.

Isolation Pads

Notes:

•

The elastomeric pads shipped (as standard) are 
adequate for most installations. For additional details 
on isolation practices, see Trane Engineering Bulletin 
Sound Ratings and Installation Guide Optimus™ 
Water-Cooled Chillers RLC-PRB015*-EN, or consult an 
acoustical engineer for sound-sensitive installations.

•

Durometer values for isolator pads are a measure of 
resilience. See 

Figure 12

.

Figure 10.

Compressor shipping spacers
C, D, E family (discharge side)

Figure 11.

Oil separator shipping bracket 

Compressor
Housing

Remove (4)
Puck-Type
Spacers

Shipping Bracket

Содержание Optimus RTHD

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды