Trane KIT15449 Скачать руководство пользователя страница 2

© 2009 Trane All rights reserved

 ACC-SVN126A-EN

Warnings, Cautions and Notices

Warnings, Cautions and Notices.

Note that warnings, cautions and notices appear at 

appropriate intervals throughout this manual. Warnings are provided to alert installing contractors 
to potential hazards that could result in personal injury or death. Cautions are designed to alert 
personnel to hazardous situations that could result in personal injury, while notices indicate a 
situation that could result in equipment or property-damage-only accidents.

Your personal safety and the proper operation of this machine depend upon the strict observance 
of these precautions.

NOTICE

Check the label on the kit to make sure it corresponds to the unit model number.  Never install 
this kit on units not listed on the kit label.

NOTICE

Improper installation or miss-applying this kit can result in an ineffective fix and cause early 
discharge line failure.

NOTICE

All brackets and weights in this kit must be installed.

ATTENTION:

 

Warnings, Cautions and Notices appear at appropriate sections throughout 

this literature. Read these carefully.

 

WARNING:

 Indicates a potentially hazardous situation which, if not avoided, could 

result in death or serious injury.

CAUTION:

 Indicates a potentially hazardous situation which, if not avoided, could 

result in minor or moderate injury. It could also be used to alert against unsafe practices.

NOTICE

:

 Indicates a situation that could result in equipment or property-damage only 

accidents.

Parts List 

Required Tools

KIT15449 Voyager 2 R410A bracket kit

1

Base Bracket for R410A units

7/16" box end ratchet wrench 

1

Tube to Tube Bracket 

5/16" magnetic bit

5

7/8" Tube Clamp 

10" magnetic bit extension.

12

1/4" Flange Nuts 

Battery operated drill motor

3

#10 Sheet Metal Screws 

Magnetic Pick up Tool

1

Installation Instructions 

2

Weights

Содержание KIT15449









Отзывы: