Trane IntelliPak 2 Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 199 / 220

RT-SVX24Q-EN 199
Figure 149. Oil injection solenoid valve
Oil injection solenoid
Table 75. Oil charge per compressor
Compressor
Pints
CSHN374 15.2
CSHN176 thru 315 and VZH170 14.2
Table 76. Torque requirements for rotolock fittings
CSHN* and VZH170
100 +/- 10 ft-lbs
N No otte e:: Always replace gasket when reassembling oil
equalizer lines.
VFD Programming Parameters (Supply/
Return/Exhaust Inverters)
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e w w//C Ca ap pa acciitto orrss!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err a an nd d d diisscch ha arrg ge e
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss a an nd d d diisscch ha arrg ge e a allll m mo otto orr sstta arrtt//rru un n
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an nn no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. F Fo orr v va arriia ab blle e
ffrre eq qu ue en nccy y d drriiv ve ess o orr o otth he err e en ne errg gy y sstto orriin ng g
cco om mp po on ne en nttss p prro ov viid de ed d b by y T Trra an ne e o orr o otth he errss,, rre effe err tto o
tth he e a ap pp prro op prriia atte e m ma an nu uffa accttu urre err’’ss lliitte erra attu urre e ffo orr
a allllo ow wa ab blle e w wa aiittiin ng g p pe erriio od dss ffo orr d diisscch ha arrg ge e o off
cca ap pa acciitto orrss.. V Ve erriiffy y w wiitth h a a C CA AT T IIIIII o orr IIV V v vo ollttm me ette err
rra atte ed d p pe err N NF FP PA A 7 70 0E E tth ha att a allll cca ap pa acciitto orrss h ha av ve e
d diisscch ha arrg ge ed d..
F Fo orr a ad dd diittiio on na all iin nffo orrm ma attiio on n rre eg ga arrd diin ng g tth he e ssa affe e
d diisscch ha arrg ge e o off cca ap pa acciitto orrss,, sse ee e P PR RO OD D--S SV VB B0 06 6* *--E EN N..
Units shipped with an optional variable frequency drive
(VFD) are preset and run tested at the factory. If a
problem with a VFD occurs, ensure that the
programmed parameters listed in Table 77, p. 201 have
been set before replacing the drive.
V Ve erriiffy y P Pa arra am me ette errss
Verify parameter 1-23 is set to 60 Hz.
1. To check parameter 1-23 press the Main Menu
button twice (if TR150 drive) (press the Back button
if the main menu does not display)
2. Scroll down to Load & Motor, press OK
3. Select 1-2, press OK
4. Press down until parameter 1-23 is displayed.
Parameter 1-23 can then be modified by pressing
OK and pressing the Up and Down buttons.
5. When the desired selection has been made, press
OK .
Should replacing the VFD become necessary, the
replacement is not configured with all of Trane's
operating parameters. The VFD must be programmed
before attempting to operate the unit.
To verify and/or program a VFD, use the following
steps:
1. At the unit, turn the 115 volt control circuit switch to
the Off position.
2. Turn the 24 volt control circuit switch to the Off
position.
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e w w//C Ca ap pa acciitto orrss!!
F Fa aiillu urre e tto o d diisscco on nn ne ecctt p po ow we err a an nd d d diisscch ha arrg ge e
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss a an nd d d diisscch ha arrg ge e a allll m mo otto orr sstta arrtt//rru un n
cca ap pa acciitto orrss b be effo orre e sse errv viicciin ng g.. F Fo ollllo ow w p prro op pe err
llo occkko ou utt//tta ag go ou utt p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err
cca an nn no ott b be e iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. F Fo orr v va arriia ab blle e
ffrre eq qu ue en nccy y d drriiv ve ess o orr o otth he err e en ne errg gy y sstto orriin ng g
cco om mp po on ne en nttss p prro ov viid de ed d b by y T Trra an ne e o orr o otth he errss,, rre effe err tto o
tth he e a ap pp prro op prriia atte e m ma an nu uffa accttu urre err’’ss lliitte erra attu urre e ffo orr
a allllo ow wa ab blle e w wa aiittiin ng g p pe erriio od dss ffo orr d diisscch ha arrg ge e o off
cca ap pa acciitto orrss.. V Ve erriiffy y w wiitth h a a C CA AT T IIIIII o orr IIV V v vo ollttm me ette err
rra atte ed d p pe err N NF FP PA A 7 70 0E E tth ha att a allll cca ap pa acciitto orrss h ha av ve e
d diisscch ha arrg ge ed d..
F Fo orr a ad dd diittiio on na all iin nffo orrm ma attiio on n rre eg ga arrd diin ng g tth he e ssa affe e
d diisscch ha arrg ge e o off cca ap pa acciitto orrss,, sse ee e P PR RO OD D--S SV VB B0 06 6* *--E EN N..
IIm mp po orrtta an ntt:: HIGH VOLTAGE IS PRESENT AT TERMINAL
BLOCK OR UNIT DISCONNECT SWITCH.
3. To modify parameters:
a. Press Main Menu twice (if TR150 drive) (press
Back if the main menu does not display)
b. Use the Up and Down buttons to find the
parameter menu group (first part of parameter
number)
c. Press OK
S Se errv viicce e a an nd d M Ma aiin ntte en na an ncce e