Trane Foundation GBC Series, Инструкция по установке, эксплуатации и обслуживанию

Страница: 17 / 40

RT-SVX069A-EN 17
A condensate trap must be installed at the unit due to
the drain connection being on the “negative pressure”
side of the fan.
A condensate drain line must be connected to the P-
Trap. Pitch the drain lines at least 0.5-inch for every 10
feet of horizontal run to assure proper condensate flow.
Do not allow the horizontal run to sag causing a
possible doubletrap condition which could result in
condensate backup due to “air lock”.
Filter Installation
Each unit ships with 2-inch filters installed. The
quantity of filters is determined by unit size. Access to
the filters is obtained by removing the filter access
panel.
N No otte e:: Do not operate the unit without filters.
Field Installed Power Wiring
An overall dimensional layout for the standard field
installed wiring entrance into the unit is illustrated in
“Unit Weights,” p. 13 . To insure the unit’s supply
power wiring is properly sized and installed, follow the
guidelines outlined below.
N No otte e:: All field installed wiring must conform to NEC
guidelines as well as state and Local codes.
Verify that the power supply available is compatible
with the unit’s nameplate ratings. The available supply
power must be within 10 percent of the rated voltage
stamped on the nameplate. Use only copper
conductors to connect the power supply to the unit.
N NO OT TIIC CE E
U Usse e C Co op pp pe err C Co on nd du ucctto orrss O On nlly y!!
F Fa aiillu urre e tto o u usse e cco op pp pe err cco on nd du ucctto orrss cco ou ulld d rre essu ulltt iin n
e eq qu uiip pm me en ntt d da am ma ag ge e a ass tth he e e eq qu uiip pm me en ntt w wa ass n no ott
d de essiig gn ne ed d o orr q qu ua alliiffiie ed d tto o a acccce ep ptt o otth he err tty yp pe ess o off
cco on nd du ucctto orrss..
IIm mp po orrtta an ntt:: A field supplied disconnect switch must be
installed at or near the unit in accordance
with the National Electrical Code (NEC
latest edition).
Main Unit Power
W WA AR RN NIIN NG G
P Prro op pe err F Fiie elld d W Wiirriin ng g a an nd d G Grro ou un nd diin ng g
R Re eq qu uiirre ed d!!
F Fa aiillu urre e tto o ffo ollllo ow w cco od de e cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
A Allll ffiie elld d w wiirriin ng g M MU US ST T b be e p pe errffo orrm me ed d b by y q qu ua alliiffiie ed d
p pe errsso on nn ne ell.. IIm mp prro op pe errlly y iin nsstta alllle ed d a an nd d g grro ou un nd de ed d
ffiie elld d w wiirriin ng g p po osse ess F FIIR RE E a an nd d E EL LE EC CT TR RO OC CU UT TIIO ON N
h ha azza arrd dss.. T To o a av vo oiid d tth he esse e h ha azza arrd dss,, y yo ou u M MU US ST T ffo ollllo ow w
rre eq qu uiirre em me en nttss ffo orr ffiie elld d w wiirriin ng g iin nsstta alllla attiio on n a an nd d
g grro ou un nd diin ng g a ass d de essccrriib be ed d iin n N NE EC C a an nd d y yo ou urr llo occa all//
sstta atte e//n na attiio on na all e elle eccttrriicca all cco od de ess..
Standard Wiring
The electrical service must be protected from over
current and short circuit conditions in accordance with
NEC requirements.
Protection devices must be sized according to the
electrical data on the nameplate.
• A field supplied disconnect switch must be installed
at or near the unit in accordance with the National
Electrical Code (NEC latest edition).
• Location of the applicable electrical service
entrance is illustrated in
“Unit Weights,” p. 13 .
Complete the unit’s power wiring connections onto
either; the main terminal block inside the unit
control panel, or the electric heat terminal block.
Refer to the customer connection diagram that
shipped with the unit for specific termination
points.
• Provide proper grounding for the unit in accordance
with local and national codes.
Control Power Transformer
The 24-volt control power transformers are to be used
only with the accessories called out in this manual.
Controls using 24 Vac
Before installing any connecting wiring, refer to “Unit
Weights,” p. 13 for the electrical access locations
provided on the unit and for AC conductor sizing
guidelines.
N NO OT TIIC CE E
U Usse e C Co op pp pe err C Co on nd du ucctto orrss O On nlly y!!
F Fa aiillu urre e tto o u usse e cco op pp pe err cco on nd du ucctto orrss cco ou ulld d rre essu ulltt iin n
e eq qu uiip pm me en ntt d da am ma ag ge e a ass tth he e e eq qu uiip pm me en ntt w wa ass n no ott
d de essiig gn ne ed d o orr q qu ua alliiffiie ed d tto o a acccce ep ptt o otth he err tty yp pe ess o off
cco on nd du ucctto orrss..
1. Use copper conductors unless otherwise specified.
2. Ensure that the AC control wiring between the
controls and the unit’s termination point does not
IIn nsstta alllla attiio on n