Trane CVHH CenTraVac, Инструкция по установке, эксплуатации и обслуживанию

Страница: 106 / 128

106 CVHH-SVX001G-EN
logs can be reviewed to identify any developing trends
in the chiller’s operating conditions. For example, if the
machine operator notices a gradual increase in condensing pressure during a month’s time, she can
systematically check and then correct the possible
cause of this condition.
Normal Operation
Table 25. Normal operation
Operating Characteristic Normal Reading
Approximate Evaporator Pressure 8 to 13.2 psia (55.2 to 91.0 kPaA) / -6.7 to -1.5 psig (-46.2 to -10.3 kPaG)
Approximate Condenser Pressure (a) 24.2 to 37.7 psia (166.9 to 259.9 kPaA) / 9.5 to 23 psig (65.5 to 158.6 kPaG) (standard condenser)
Oil Sump Temperature Unit not running 110°F to 135°F (43.3°C to 57.2°C)
Oil Sump Temperature Unit running 110°F to 160°F (43.3°C to 71.1°C)
Oil Sump Differential Oil Pressure
(b)
20 to 24 psid (137.9 to 165.5 kPaD)
(a) Condenser pressure is dependent on condenser water temperature, and should equal the saturation pressure of R-1233zd at a temperature above that of
leaving condenser water at full load.
(b) Oil tank pressure: -7 to -4 psig (-48.3 to -27.6 kPaG). Discharge oil pressure: 13 to 20 psig (89.6 to 137.9 kPaG).
N NO OT TIIC CE E
E Eq qu uiip pm me en ntt D Da am ma ag ge e!!
F Fa aiillu urre e tto o rre em mo ov ve e tth he e ssttrra aiin n rre elliie eff w wiitth h tth he e sse en nsso orr
cco ou ulld d rre essu ulltt iin n e eq qu uiip pm me en ntt d da am ma ag ge e..
D Do o N NO OT T a atttte em mp ptt tto o p pu ullll sse en nsso orr b bu ullb b tth hrro ou ug gh h tth he e
ssttrra aiin n rre elliie eff;; a allw wa ay yss rre em mo ov ve e tth he e e en nttiirre e ssttrra aiin n rre elliie eff
w wiitth h tth he e sse en nsso orr..
Table 26. Recommended maintenance
Daily Every 3 months Every 6 months Annually (a)
,
(b)
Check the chiller’s evaporator and
condenser pressures, oil tank
pressure, differential oil pressure,
and discharge oil pressure.
Compare the readings with the
values provided in the preceding
table.
Check the oil level in the chiller oil
sump using the two sight glasses
provided in the oil sump head.
When the unit is operating, the oil
level should be visible in the lower
sight glass.
Complete logs on a daily basis.
Clean all water strainers in the
water piping system.
Lubricate the vane control linkage
bearings, ball joints, and pivot
points.
Lubricate vane operator tang O-
rings.
Operate the tang operators
manually and check for any
abnormalities.
Drain contents of the rupture disk
and purge discharge vent-line
drip-leg into an evacuated waste
container. Do this more often if the
purge is operated excessively.
Apply oil to any exposed metal
parts to prevent rust.
Shut down the chiller once each year to check the
items listed on the
“Appendix D: CVHH
CenTraVac ™ Chiller Annual Inspection List,” p.
123 (refer to “Appendix A: Forms and Check
Sheets,” p. 118 ).
Perform the annual maintenance procedures
referred to in
“Maintenance,” p. 110 .
R Re ecco om mm me en nd de ed d M Ma aiin ntte en na an ncce e