Trane BAYECON353 Series Скачать руководство пользователя страница 16

Страница: 16 / 24

Economizer Controller

ACC-SVN203C-EN

SETPOINTS

EXH2 SET

75%

0 to 100%;

increment by 1

N/A

EXH2 SET is not available

SYSTEM

SETUP

INSTALL

(c)

1/1/2011

Present date

Display order = MM/DD/YY

Setting order = DD, MM, then YY

UNITS DEG

(c)

ºF

°F or °C

ºF

Sets economizer controller in degrees Fahrenheit or

Celsius

EQUIPMENT

(c)

CONV

CONV = conventional

HP is not available

AUX2 I

(c)

N/A

Shutdown (SD)

Heat (W1)

HP(O)

HP(B)

Heat (W1)

In CONV mode:

SD = Enables configuration of shutdown (default);

W = Informs controller that system is in heating

mode

NOTE: If using 2-speed fan mode, you must

program CONV mode for W. Shutdown is not

available in the two-speed fan mode

In HP O/B mode:

HP(O) = energize heat pump on Cool (default);

HP(B) = energize heat pump on Heat

FAN SPEED

(c)

1 speed

1 speed/

2 speed

See unit

nameplate:

Digit 15 = 0 or 1 - 1

speed;

Digit 15 = 7 or 9 - 2

speed

Sets economizer controller for operation of 1 speed

or 2 speed supply fan. The controller does not

control the fan but positions the OA and RA dampers

to the heating or cooling mode. See

page 23 for modes and position

NOTE: 2-speed fan option also needs Heat (W1)

programmed in AUX 2 In

FAN CFM

(c)

5000cfm

100 to 15000

cfm;

increment by

100

5000cfm

This is the capacity of the RTU. The value is found

in the Unit Catalog. The cfm of the fan is only used

with DCV CAL ENABLE AUO

AUX1 OUT

NONE

ERV

EXH2

SYS

NONE

AUX1 OUT is a programmable output used for

System Alarm output

OCC

(c)

INPUT

INPUT or

ALWAYS

When using a setback thermostat with occupancy

out (24 Vac), the 24 Vac is input “INPUT” to the OCC

terminal. If no occupancy output from the

thermostat then change program to “ALWAYS” OR

add a jumper from terminal R to OCC terminal

FACTORY DEFAULT

(c)

NO or YES

Resets all set points to factory defaults when set to
YES. LCD will briefly flash YES and change to NO but
all parameters will change to factory default values

ADVANCED

SETUP

MA LO SET

(c)

45ºF

35 to 55°F;

increment by 1°F

45ºF

Temp to activate Freeze Protection (close damper or
modulate to MIN POS if temp falls below set value)

FREEZE POS

(c)

CLO

CLO
MIN

CLO

Damper position when freeze protection is active

(closed or MIN POS)

ZERO

(c)

0ppm

0 to 500 ppm;

increment by 10

0ppm

ppm level to match CO

sensor start level. 0-

10 Vdc CO

sensors require CO2 ZERO to be 400

SPAN

(c)

2000ppm

1000 to 3000

ppm;

increment by 50

2000ppm

ppm span to match CO

sensor; e.g.; 500-1500

sensor output would be 500 CO

zero and 1000 CO

span. 0-10 Vdc CO

sensors require CO

SPAN to be

1600

STG3 DLY

2.0h

0 min, 5 min, 15

min, then 15

min intervals.

Up to 4h or OFF

2.0h

Delay after stage 2 for cool has been active. Turns

on 2nd stage of mechanical cooling when

economizer is 1st stage call and mechanical cooling

is 2nd stage call. Allows three stages of cooling, 1

economizer and 2 mechanical. OFF = no Stage 3

cooling

Table 4.

Controller menu structure (continued)

Menu Parameter

Parameter

Default

Value

Parameter
Range and

Increment

(a)

Parameter

Recommended

Value

(b)

Notes

Содержание BAYECON353 Series

























Результаты поиска

Содержание BAYECON353 Series

Отзывы:

Trane BAYECON353 Series, Руководство по установке, Страница: 16 / 24

Результаты поиска

Содержание BAYECON353 Series

Отзывы: