Trane Technologies Thermo King Heat King HK450 страница 40 Скачать руководство пользователя

Страница: 40 / 44

TK 56117-6-OP-EN

Troubleshooting

The following information is provided to assist you in locating and
correcting minor problems. If these procedures do not correct the problem,
contact your nearest Thermo King dealer or authorized service center.

Condition

Possible Cause

Remedy

Unit switch ON - nothing
happens

Dead battery

Recharge or replace battery

Blown fuse

Turn unit off and correct
cause

Replace fuse

Poor battery connections

Clean and tighten

Shutdown alarm

See Alarm Codes section of
this manual

Unit maintenance switch is
switched OFF

Turn switch to ON position

Unit switch ON -
indicator lights come on
but engine does not
crank

Corroded battery
connections

Clean and tighten

Engine cranks but fails to
start

No fuel or wrong fuel in tank

Fill fuel tank
After filling a completely
empty tank, bleed fuel
system

Engine too cold

Preheat unit for correct
amount of time; see
Starting Instructions

Glow plugs defective

Replace glow plugs

Air in fuel system

Bleed fuel system

Also check if fuel lines are
tight and filters are clean

Air in injection pump

Bleed fuel system

Defective electric fuel pump

Replace fuel pump

Plugged electric fuel pump

Remove restriction

Engine stops after starting

Fuel filter obstructed

Replace filter element

Содержание Thermo King Heat King HK450













































Результаты поиска

Содержание Thermo King Heat King HK450

Отзывы:

Похожие инструкции для Thermo King Heat King HK450

Бренды по названию

Популярные бренды

Trane Technologies Thermo King Heat King HK450, Руководство оператора

Результаты поиска

Содержание Thermo King Heat King HK450

Отзывы:

Похожие инструкции для Thermo King Heat King HK450

Бренды по названию

Популярные бренды