background image

1)  Open the Door and remove the Porcelain Grill, Grease Drain Pan Assembly from inside the 

Grill. 

2)  

IMPORTANT: Remove all unburned Pellets and ash from inside and around 

     the Firepot. 

A shop-vac is ideal tor this task 

CAUTION! ASSURE THAT THE 

     GRILL IS COLD TO AVOID A FIRE FROM HOT ASH.

 

3)  Replace the Grease Drain Pan Assembly and the Porcelain Grill and initiate start-up 

procedure. 

4)  If this didn’t remedy the problem, contact Traeger Technical Support 

(SECTION SEVEN)

 

for additional troubleshooting help. 

 

THE AUGER MAKES A LOT OF NOISE WHEN I TURN THE GRILL ON AND I HAVE 
NOTICED A DROP IN THE GRILL TEMPERATURE. WHAT CAN I DO TO CORRECT 
THIS? 

In Grill models with a fixed Auger Drive Motor, you will need to “TRUE” the Auger 
1)  Remove all Pellets from the Pellet Hopper and run Pellets out of the Auger Tube. 
2)  Remove the screw connecting the Auger Drive Motor shaft to the Auger shaft, using a 7/64 

hex wrench and a 5/16 wrench or driver. 

3)  Spin the Auger shaft over the Auger Drive Motor shaft. It should rotate freely, without 

binding. 

4)  If the Auger shaft binds, loosen the two bolts mounting the Auger Drive Motor/Bracket 

assembly to the Burner Box with a 7/16 wrench. 

5)  Move the Auger Drive Motor/Bracket assembly until you can feely rotate the Auger shaft 

over the Auger Drive Motor shaft. 

6)  Re-tighten the 7/16 bolts, making sure that the Auger End Piece Shaft still freely rotates 

over the Auger Drive Motor shaft. 

7)  Reinstall the screw and nut connecting the Auger Drive Motor shaft to the Auger shaft. 
        

WITH THE TRAEGER DIGITAL CONTROL, WHAT DIAL SETTING IS RECOMMENDED 
FOR STARTING THE GRILL?  

     The auto-start procedure is the same for all Grill Controls. With the Door open, turn the 

Switch/Dial ON and Temperature Dial to SMOKE. In approximately 2 minutes you will 
notice whitish-gray smoke coming out of the Grill as the Pellets ignite. After assuring the 
Pellets have ignited, close the Door and set the Temperature Dial to any cooking setting 
desired.   

 

HOW DO I PROTECT MY PAINT FINISH? 

1)  Use a protective Cover on the Grill and touch-up paint to repair any scratches. 

TRAEGER GRILL COVER to protect the Grill is highly recommended! Covers and 
touch-up paint are available from your local Traeger Dealer, or log on to our Web Site 
 

www.traegergrills.com

. 

2)  Every 90 days, use a high quality car wax on the outside surfaces of the Grill. ONLY 

APPLY WAX TO A COLD GRILL. 

 

WHERE CAN I GET A NEW PART FOR MY GRILL? 

Check with your Traeger Dealer. They may have the part in stock or can order the part 
for you. Or you can contact the Traeger Parts Department 

(SECTION SEVEN) 

to place 

an order. In either case, please provide your name, phone number, address, Model and 
Serial Number of the Grill (located on a label inside the Hopper Lid), along with the part 
identification. 

 
 
 

Содержание BBQ020LE



















Отзывы: