Tradesman MAGNESIUM 8520 Скачать руководство пользователя страница 3

AIR SUPPLY AND CONNECTIONS 

 
 

 

The compressed air power source shall be pressure-regulated.  The regulated 

pressure must not exceed the maximum air pressure marked on the tool.  If a 

regulator fails, the pressure delivered to the tool must not exceed 1.5 times the 

maximum air pressure, or 180 PSI, whichever is greater. 

 

Pressure regulators shall be used to limit the air pressure supplied to the tool.  

Regulators shall be set at an operating pressure which is lower than or equal to the 

tool manufacturer’s specified maximum air pressure. 

 

Air supply hoses shall have a minimum working pressure rating equal to or greater 

than the pressure from the power source if a regulator fails, or 120 PSI, whichever is 

greater. 

 

Tools shall be fitted with a fitting or hose coupling on or near the tool in such a manner 

that all compressed air in the tool is discharged at the time the fitting or hose coupling 

is disconnected.  

 

 

Many air tool users find it convenient to use an 
oilier to help provide oil circulation throughout 
the tool and to increase the efficiency and useful 
life of the tool. Check oil level in the oilier daily. 

 

 

Many air tool users find it convenient to use a 
filter to remove liquids and impurities which can 
rust or wear internal parts of the tool. A filter can 
also increase the efficiency and usefulness 
of the tool. The filter must be checked on a daily 
basis, and if necessary, drained. 

 

 

For better performance, install a 3/8” quick 
connector (1/4” NPT threads) with an inside 
diameter of .315” on your tool and a 3/8” quick 
coupler on the air hose. 

 
 

The following illustration shows the correct mode of connection to the air supply 
system which will increase the efficiency and useful life of the tool. 

 
 
 
 
 
 
 
 
 
 
 

TESTING THE SAFETY TRIP MECHANISM 

 

Never point any operational fastener driving tool at yourself or at any other 
person. 

 

 

Disconnect the air supply from the tool. 
 
 
 
 
 

 

Insert a stick of fasteners into the magazine.  See section 
on “Loading Fasteners Into Stapler”. 
 
 
 
 

 

Press down on workpiece and release the contact safety 
trip mechanism.  Verify there is no binding, sticking or 
jamming of this mechanism. 

 
 
 

 

Reconnect the air supply to the tool. 
 
 
 
 
 

 

Depress the contact safety trip mechanism against the 
workpiece without pulling the trigger. The tool must not 
cycle. Never use the tool if a cycle occurs. 
 
 

 

Hold the tool clear of the workpiece. The contact safety trip 
mechanism should return to its original down position. Pull 
the trigger. The tool must not cycle. Do not use the tool if a 
cycle occurs. 
 
 

 

To complete the testing procedures, depress the contact 
safety mechanism against the workpiece and pull the 
trigger, the tool must cycle. 
 

 

4

5

Содержание MAGNESIUM 8520









Отзывы: