TracVision C3 Скачать руководство пользователя

Страница: 2 / 24

Before you begin, follow these steps to make sure
you have everything you need to complete the
installation.

Unpack the box and ensure it contains

everything shown on the supplied Contents

List. Carefully examine all of the supplied

parts to ensure nothing was damaged in

shipment.

Gather all of the tools and materials listed

below. You will need these items to complete

the installation.

• Electric drill

• 3/16" (5 mm), 5/32" (4 mm), and

3/32" (2.25 mm) drill bits

• 1/2" wrench or nut driver

• 3/4" (19 mm) hole saw and auger bit

• Phillips and flat-head screwdrivers

• Cutting pliers

•

Linear only:

9/64" allen wrench

•

Circular only:

RG-6 or RG-11 (75 ohms) RF cable, if

installing two or more receivers

• Silicone sealant, RTV, or equivalent

• 7/16" open-end wrench

• Construction adhesive suitable for the

deck

• Augat IT1000 connector installation tool

(KVH Part #19-0242)

• Satellite TV receiver(s) for your desired

service

(see Figure 2 for a list of validated

U.S./Canadian receivers; for information on

connecting different receiver models, contact

KVH Technical Support)

Always lift the antenna by the baseplate,

never by the radome (see Figure 1).

IMPORTANT!

Figure 1: TracVision C3 Antenna

Radome

Baseplate

Figure 2: Receivers Validated for Use with TracVision C3

Standard-definition models

DIRECTV

DISH

Bell TV

D12

D11

D10

311

211k

211

3100

4100

High-definition models

DIRECTV

DISH

Bell TV

HD not

supported

211k

211

6100

6131

Inspect Parts and Get Tools

Содержание C3

























Результаты поиска

Содержание C3

Отзывы:

Похожие инструкции для C3

Бренды по названию

Популярные бренды

TracVision C3, Руководство по установке

Результаты поиска

Содержание C3

Отзывы:

Похожие инструкции для C3

Бренды по названию

Популярные бренды