46
M
AINTENANCE
S
T
AR
T
ER
/
GENERA
T
OR
B
EL
T
Check the starter/generator belt at the initial service and then intervals indicated in the
N
eve
r allo
w
t
he
t
e
nsion to
exceed
16
0
l
b
s
(73 kg) wh
il
e
installin
g
t
he be
lt
.
At t
he
ti
me
of installation
,
t
he be
lt
mu
st not
be
roll
ed
o
ve
r t
he
install
ed edge
s of t
he
start
e
r
/ge
n
e
rator or
d
ri
ve c
l
u
t
ch
p
u
ll
ey
s
.
E
xce
ssi
ve
str
e
t
ch
in t
he be
lt
c
an
c
a
u
s
e c
or
d
fail
u
r
e.
A
NOTICE: A loose belt can cause audible vibration and squeal.
1.
New belt:
a.
Tighten a new starter/generator belt to 25 - 30 lbs. (110 -
130 N) tension when a gauge is applied half way between
the two pulleys.
b.
A new belt may be checked manually. A maximum deflection
of 3/8” (10 mm) is acceptable.
2.
E
xisting
belt:
a.
Tighten an existing belt to 17 - 18 lbs. (75 - 80 N) tension
using the same technique.
b.
Inspect for cracks or wear. A maximum deflection of 1/2” (13
mm) is acceptable.
A
dju
stin
g
t
he Be
lt
1.
Loosen the starter/generator pivot bolt.
2.
While holding the lower adjusting nut with a wrench, loosen the upper jam nut with another wrench. Move the
lower nut up or down the adjustment bolt until the correct belt tension is achieved.
3.
Hold the lower nut in place and tighten the upper jam nut against it.
4.
Tighten the starter/generator pivot bolt.
AIR IN
T
A
K
E AN
D
COOLING
F
INS
Kee
p t
he e
n
g
in
e c
oolin
g c
o
m
po-
n
e
nts
c
l
e
an to r
educe
t
he
ris
k
of
o
ve
r
he
atin
g
an
d
t
he
possi
b
l
e
i
g
ni-
tion of a
ccumu
lat
ed deb
ris
.
Dirt and debris can clog the engine air cooling system. Allow
the engine to cool and use the following guidelines after
every off-road use:
• Check for a build up of dirt and debris in the air intake and
cooling fins.
• Clean the areas shown to prevent engine damage.
• Make sure the linkages, springs and controls are clean.
• Make sure the area around the muffler is free of any com-
bustible material.
Regular maintenance of the cooling system is required to ensure an adequate supply of air to the cooling fins. Com-
pressed air can be used for routine cooling system maintenance.
Clean the cooling system at the intervals indicated in the
T
ools
• Belt Tension Gauge
• Ratchet
• Wrench, 3/4”
• Socket, 3/4”
• Wrench, 9/16”
3/8" (1 cm) Maximum
Deflection (New Belt)
1/2" (1.3 cm) Maximum
Deflection (Existing Belt)
Содержание OX 400 2020
