Features
• Lightweight – Approximately 1/2 of the
weight of equivalent capacity Sealed Lead Acid
batteries
• Flat discharge curve – Constant power for
longer
• Fuel Gauge – Displays battery power status
• Different connection options
• Folding carry handle
• Protected against:
overcharge, over temperature, over current,
deep discharge, short circuit.
Precautions in use
• DO NOT attempt to dismantle the battery pack
in any way
• DO NOT short circuit your battery pack – it
could overheat and cause fire or explosion
• DO NOT use as a cranking battery or for start-
ing an engine
• Your battery pack will need to be charged fully
before use
• If storing your battery pack, store in a charged
state. Recharge every 4 months
• Charge your battery directly after each use.
Leaving your battery in a fully discharged state
will seriously and permanently damage its per-
formance
• It is recommended to recharge the battery pack
within 12 hours if fully discharged
• Excess heat will degrade the battery pack
rapidly. Always store your battery pack in a cool
dry place
• DO NOT leave for long periods in the sun or in
a hot vehicle
• DO NOT immerse your battery pack in water
• DO NOT dispose of in normal household refuse.
USB connectors operation
The battery is fitted with three USB outputs.
These need to be turned on to give an output.
These are turned on and off as follows:
• Press and hold the fuel gauge button for
at least 3 seconds (the fuel gauge will show
the status of the battery during these three
seconds) until the bottom red LED starts
flashing, then release holding the button.
• The USB outputs are now turned on and the
red LED will keep flashing to indicate this.
• Whilst these USB outputs are activated,
to observe the battery status then just
momentarily press the Fuel Gauge push
button.
• The USB outputs will draw a small amount of
current from the battery and must be turned
off when not in use.
• To turn the USB outputs off then press
and hold the fuel gauge button for at least
3 seconds until the bottom red LED stops
flashing.
Optional Accessories
The following optional accessories are available
TR8125 - Eyelets to 12V Socket
TR8405 - EC5 to 2.5 DC Plug
TR8409 - EC5 to 2.1 DC Plug
TR8100/1 - Neoprene carry case
Please visit
tracerpower
.com to see a full
list of available accessories.
Congratulations on purchasing the latest in portable battery pack technology from Tracer Power.
Please take a moment to read carefully the following instructions to get the best performance
from your Lithium battery pack.
LITHIUM IRON PHOSPHATE BATTERY PACKS
(LiFePO4)
With spring loaded grab-handle.
Recharging the battery pack
• Only use the LiFePO4 charger supplied with
the battery pack, or a Tracer approved charger.
Visit
tracerpower
.com for information on more
chargers.
• Do not use this charger for any other purpose.
It has been designed to be used with Tracer
LiFePO4 battery packs only.
1. Plug the charger into AC mains – the LED light
on the charger will glow GREEN
2. Plug the charger lead firmly into the battery
pack’s Charge port – the LED light on the charger
will change to RED to indicate charging
3. When the LED light changes back to GREEN the
battery pack is fully charged
4. Disconnect the charger from the battery pack
and from the AC mains
Additional charging information
DO NOT leave the charger connected to the
battery for long periods after the battery is
charged.
Charging voltage: 27.6V – 29.2V
Charge time: 4-6 hours (with supplied charger)
Uninterrupted Power Supply (UPS): It is
possible to use the battery pack whilst on
charge. The application’s current requirement
must not exceed the charger’s current, i.e. 2A
with supplied charger.
Code
Model
Dimensions (mm)
Weight
Charge Time (hrs) Run time(hrs) Max discharge current
A B C D
12V 4A 12V 10A 100W Continuous Peak (for 10ms)
BP2564
12V 16Ah
165 125 110 35 2
4-6 2-3
2 30A
90A
BP2568
12V 24Ah
165 160 110 35
2.9
6-8 3-4
3 30A
90A
BP2578
24V 8Ah
165 125 110 35
2
4-6 2-3
2 15A
30A
A
B
C
BP2564
BP2568
BP2578
D
BP2568
12V 24Ah
165 125 110 46
2.9
24V 2A 24V 5A
