background image

 

Preliminary Preliminary User's Manual  l  TQMaX4XxL UM 0001  l  © 2022, TQ-Systems GmbH 

 

Page  1 

 

 

1.

 

ABOUT THIS MANUAL 

1.1

 

Copyright and license expenses 

Copyright protected © 2022 by TQ-Systems GmbH. 
This Preliminary User's Manual may not be copied, reproduced, translated, changed or distributed, completely or partially in 

electronic, machine readable, or in any other form without the written consent of TQ-Systems GmbH. 
The drivers and utilities for the components used as well as the BIOS are subject to the copyrights of the respective 

manufacturers. The licence conditions of the respective manufacturer are to be adhered to. 
Bootloader-licence expenses are paid by TQ-Systems GmbH and are included in the price. 
Licence expenses for the operating system and applications are not taken into consideration and must be calculated / declared 

separately. 
 
 

1.2

 

Registered trademarks 

TQ-Systems GmbH aims to adhere to copyrights of all graphics and texts used in all publications, and strives to use original  

or license-free graphics and texts. 
All brand names and trademarks mentioned in this Preliminary User's Manual, including those protected by a third party, unless 

specified otherwise in writing, are subjected to the specifications of the current copyright laws and the proprietary laws of the 

present registered proprietor without any limitation. One should conclude that brand and trademarks are rightly protected by a 

third party. 
 
 

1.3

 

Disclaimer 

TQ-Systems GmbH does not guarantee that the information in this Preliminary User's Manual is up-to-date, correct, complete or 

of good quality. Nor does TQ-Systems GmbH assume guarantee for further usage of the information. Liability claims against TQ-
Systems GmbH, referring to material or non-material related damages caused, due to usage or non-usage of the information 

given in this Preliminary User's Manual, or due to usage of erroneous or incomplete information, are exempted, as long as there 

is no proven intentional or negligent fault of TQ-Systems GmbH. 
TQ-Systems GmbH explicitly reserves the rights to change or add to the contents of this Preliminary User's Manual or parts of it 

without special notification. 
 
Important Notice: 
Before using the Starterkit MBaX4XxL or parts of the schematics of the MBaX4XxL, you must evaluate it and determine if it is 

suitable for your intended application. You assume all risks and liability associated with such use. TQ-Systems GmbH makes no 
other warranties including, but not limited to, any implied warranty of merchantability or fitness for a particular purpose. Except 

where prohibited by law, TQ-Systems GmbH will not be liable for any indirect, special, incidental or consequential loss or damage 

arising from the usage of the Starterkit MBaX4XxL or schematics used, regardless of the legal theory asserted. 
 
 

1.4

 

Imprint 

TQ-Systems GmbH 
Gut Delling, Mühlstraße 2 
D-82229 Seefeld 
 
Tel: 

+49 8153 9308–0 

Fax: 

+49 8153 9308–4223 

E-Mail: 

Info@TQ-Group

 

Web: 

TQ-Group

 

 

Содержание TQMaX4X Series











































Отзывы: