TPS miniCHEM-pH Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

TPS miniCHEM-pH Скачать руководство пользователя страница 5

Page 5

¬

Alarm LED

The Alarm LED provides visual indication of when the control limit has been
exceeded. The control limit can be set for a “too high” or a “too low” alarm.
See section 3.5.

-

Limit Control

Adjust this control to the pH value at which the Alarm LED and (optional)
relay output are activated. See section 3.5.

®

Zero Calibrate Control

Adjust this control to calibrate the

mini

CHEM

-pH

in a pH6.88 or pH7.00

buffer. See section 4.1.

¯

Span Calibrate Control

Adjust this control to calibrate the

mini

CHEM

-pH

in a buffer several pH

away from pH7 (e.g. pH4.00 or pH9.23). See section 4.1.

°

Function Switch

The Function Switch is used to select the mode of operation. See section 2.

±

Display Window

The

mini

CHEM

-pH

has a large, easy to read LCD display. The units of

measurement are clearly shown in the window beneath the display.

Æ

Terminal Cover

The terminal cover provides easy access to all of the connections, (optional)
relay output fuse, configuration jumpers and user-adjustable trimmers. The
cover is water resistant to IP65.

«
...
3
4
5
6
7
...
»

Содержание miniCHEM-pH





























Отзывы:

Нет отзывов