TPI 265 Скачать руководство пользователя страница 26

Страница: 26 / 32

G. Trouble Shooting

Problem

Probable Causes

Does not power up

•

Dead or defective battery

•

Broken wire from battery
snap to PCB

All functions except

•

Very weak battery that will

ohms read high

not turn on the low battery
indicator on the LCD

AC Volts do not read

•

Very weak battery that will
not turn on the low battery
indicator on the LCD

AC Amps does not read

•

Make sure the jaw is clamped
around a single wire and the
device connected to the wire is
turned on.

Application Notes (AC Amps)

When measuring AC Amps of a motor there
are two types of measurements that can be
made, running current and in-rush or start-up
current. Start-up current will usually be much
higher than running current.

Set up the meter following the steps under
“Measurement Procedure” on page 17, and
then proceed with the following:

•

Clamp the meter around a single wire

and reconnect power to the device. Read
the current displayed on the meter. This
is the running current of the motor.

•

Disconnect power to the motor and put

the meter in PEAK HOLD mode.
Reconnect the power and read
the current displayed on the
meter. This is the in-rush or
start-up current
of the motor.

www.

.com

[email protected]

1.800.561.8187

Содержание 265

































Результаты поиска

Содержание 265

Отзывы:

Похожие инструкции для 265

Бренды по названию

Популярные бренды

TPI 265, Инструкция по эксплуатации

Результаты поиска

Содержание 265

Отзывы:

Похожие инструкции для 265

Бренды по названию

Популярные бренды