background image

 

II 

FCC STATEMENT 

 

This equipment has been tested and found to comply with the 
limits for a Class B digital device, pursuant to part 15 of the FCC 
Rules. These limits are designed to pro-vide reasonable 
protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not in-stalled and used in 
accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning 
the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following 
measures: 

¾

  Reorient or relocate the receiving antenna. 

¾

  Increase the separation between the equipment and 

receiver. 

¾

  Connect the equipment into an outlet on a circuit different 

from that to which the receiver is connected. 

¾

 Consult the dealer or an experienced radio/ TV technician for 

help. 

This device complies with part 15 of the FCC Rules. Operation is 
subject to the following two conditions: 
1)  This device may not cause harmful interference. 
2)  This device must accept any interference received, including 

interference that may cause undesired operation.

 

Содержание TL-SG1016













Отзывы: