background image

31

9.    A room temperature sensor is provided with approx. eight (8) feet long extension wire. It is located on the rear 

of the cabinet. Make sure that the extension wire is not touching the exhaust pipe. The room temperature 
sensor can be installed either with the self adhesive tape on the back or with a wood screw provided with the 
sensor depending on the type of surface chosen for installation.
NOTE:   Choose a location for the sensor that is not in the path of direct sunlight, drafts or the flow of warm air 

from the heater.

(a)  Self Adhesive Tape

Peel off the protective tape on the back of the sensor and expose the 
adhesives. Place the sensor on the desired location on the wall and press 
down.

(b)  Wood Screw

Screw down the wood screw provided with the heater into the desired 
location on the wall. Hook the back of the room temperature sensor.

10.  After installation is completed, secure heater to the wall with the wall brackets provided with the heater. Make 

sure the heater is parallel to the wall (See Fig. 16).

11.  Before ignition, recheck the following:

a.  All connections are tight and firm.
b.  The heater and the standard flue pipe areas are free of any materials.
c.  The heater is level and parallel to the wall.
d.  The exhaust and the intake holes of the standard flue pipe are fully exposed to outdoor air, but not 

protruded too far from the wall sleeve.

Fig. 13

NOTE:   Emergency power supply and use of 12V DC batteries with an inverter. Consult your dealer before 

attempting to use a battery/inverter system to provide power for your Laser heater. These units require 
true sine wave power for proper long-term operation. Some types of modified or block sine wave 
inverters will cause damage to the electrical components of the heater. Several inverter 
manufacturers offer true sine wave inverters which should operate the unit without any problems if 
properly sized and configured. If you have any questions about appropriate power supply, consult your 
authorized TOYOTOMI dealer.

WARNING: 

MAKE SURE POWER SUPPLY CORD IS DISCONNECTED TO AVOID ANY ELECTRIC SHOCK

BEFORE SERVICING. ELECTRIC SHOCK MAY CAUSE SERIOUS INJURY.
INSTALLATION SHOULD BE CONDUCTED BY A LICENSED ELECTRICIAN.

PERMANENT WIRING INSTALLATION

Step 1.
Disconnect power supply cord 
from power source.
Remove three (3) screws and 
control box cover on the back of 
the heater.

Step 2.
Disconnect ground wire (green 
wire) from the power supply 
cord bracket.

Step 3.
Disconnect two power
supply wires from right side of 
the terminal.

Step 4.
Squeeze strain relief with the ad- 
justable pliers to remove plastic 
bushing from the power supply 
cord bracket.
Remove the power supply cord.

Step 5.
Insert the power supply cable 
from junction box and connect 
ground wire to the power supply 
cord bracket and power wires to 
the
terminal.

Step 6.
Affix the control box cover to the 
heater and insert screws.

Содержание Laser 531





































Отзывы: