manualshive.com logo in svg

Toyotomi FF-V30T, Инструкция по установке и эксплуатации

Поделиться
Скачать
Toyotomi FF-V30T Скачать руководство пользователя страница 13

12

☞

☞

☞

1. Introduction

This section contains all the relevant information, 

specifically:

• Installation specifications

• List of installation tools

• Instructions for the installation of the Vented Heating System

The heater can be installed at any location, on condition 

that there is full compliance with electrical, fueland 

emission regulations.

Before you start installing the heating system (inclu-ding 

electrical wiring), check the local building and fire safety 

regulations. The requirements stipulated in these 

regulations must be respected in order to guarantee a 

legally approved installation and correct operation.

The heater was designed to be used to a 
maximum altitude of 1000m above sea level. 
Contact your dealer for the necessary 
adjustments if you wish to use it at a higher 
altitude.

2. Moving the heater

In addition to the space required for the heater, extra 

room must be kept free for air circulation. The Vented 

Heating System can be placed on any type of flooring 

and operate safely, unless fuel or fire safety regulations 

specify otherwise. Check the gaps in the manner 

stipulated in the instructions in the manual.

Recommended tool kit

1.   Crosshead screwdriver

2.   Steel tape measure

3.   Felt-tip pen or pencil

4.   Cement for exterior use

5.   Electric drill (clockwise and anti-clockwise recommended)

6.   Hole cutting saw, jig saw or other tools suitable 

forsawing a hole of 70~80 mm for the exhaust pipe

7.   Long drill

8.   Standard screwdrivers

9.   Volt, Ohmmeter

10. Spirit level

11. Small range of self-tapping screws

12. Insulated screwdriver

13. Protective material for your floor

14. Container for fuel exhaust pipe

3. The electrical supply system

The electrical system must be protected from overloads 

by an at least 5-Ampere fuse or contact breaker.

Some installations (such as for use in mobile 
homes) must be fitted with a permanent 
connection to the household power circuits. 
This must be done by a recognised 
electrician.

4. Wiring for the room temperature sensor

A  temperature sensor that can be fitted to a wall mea-

sures the room temperature in order to automatically 

regulate the heating. The standard sensor wire is 

approximately 2.5 m long.

The sensor may not be placed in a draught, 
direct sunlight or the warm air flowing out of 
the heater. This may cause incorrect 
temperature indications.

SECTION F:
INSTALLATION

 FF-V30T (E)  07.11.8 11:17 AM  ページ 12

Содержание FF-V30T

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды