manualshive.com logo in svg

Toyota PZQ72-48050, Инструкция по монтажу

Поделиться
Скачать
Toyota PZQ72-48050 Скачать руководство пользователя страница 7

ISSUE 

1

: 

20/03/2017

PART NUMBER: PZQ72-480

5

0

PAGE 7 OF 15

STEP 9

STEP 10

STEP 11

STEP 12 

Using a trim removal tool, remove both second row 

grab handles. Take care not to damage whilst removing.

Lower the headliner by unclipping the three trim clips 

at the rear of the vehicle and two trim clips above the 

second row seats, using a trim removal tool.

Lower the headliner and place the cant rail template 

(Pg.13) over the existing holes as shown on template.

Drill all holes as marked on template.

Note: Ensure a 10mm drill stop is used. Take care not 

to damage washer 

fl

 uid line.

Remove all sharp edges from holes using a de-burring 

tool.

Remove swarf and c oat all raw edges with an anti-rust 

grease.

Insert an anchor plate through panel cavity and align 

with drilled holes.

Place cover plate over holes and align the anchor and 

cover plate.

Secure the cover plate to the anchor plate using the 

M6x16mm button head bolts and M6 spring 

washers.

TORQUE: M6: 13Nm

Insert supplied M10 spike into anchor plate as shown.

Place masking tape on the underside of the headliner 

and depress the headliner so the position of the spike 

protrudes through. Mark the location of these points

Place a block of wood behind the marked location and 

drill using a 19mm vinyl cutter.

Reinstall the vehicle headliner

CLIP LOCATIONS

Содержание PZQ72-48050













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды