Toyota PT922-12170 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 24

background image

SCION

iM

2016 -

INTERIOR LIGHT KIT

Procedure

Page 2 of 24 pages

Issue: C 01/28/2016

DIO

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.

These guidelines can be found in the "Accessory Installation Practices" document.

This document covers such items as:-



Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).



Safety (eye protection, rechecking torque procedure, etc.).



Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).



Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).

Please see your Scion dealer for a copy of this document.

1.

Prepare for the Installation.

(a)

Install DCC fuse, if necessary.

(b)

Check the following for damage or

malfunction:

(1)

Internal and external trim & body work.

(2)

Radio pre-set stations.

(3)

Automatic climate control systems (i.e.

temperature control, A/C, fan speed, vent

modes, rear defrost, etc.)

(4)

Other functions (i.e. security, hazard

lights, etc.).

«
1
2
3
4
...
»

Содержание PT922-12170

























Отзывы:

Нет отзывов

Похожие инструкции для PT922-12170

Бренд: Mamiya Страницы: 4

Бренд: Makita Страницы: 20

ETIQUETTE MEMOIRE M I740N

Бренд: Aastra Страницы: 1

Бренд: Allen Sports Страницы: 2

Fireplace Surrounds None

Бренд: Dimplex Страницы: 2

Бренд: Gira Страницы: 10

Бренд: Prorack Страницы: 14

Бренд: Ericsson Страницы: 487

Ocean Seven 304Plus

Бренд: idronaut Страницы: 79

Бренд: APOLON Страницы: 19

E-Bike Frontlight E 80

Бренд: RFR Страницы: 2

BELL SYSTEM FG-16 V3

Бренд: M-E Страницы: 2

Бренд: Lennox Страницы: 10

Бренд: Montgomery Ward Страницы: 4

Бренд: Bioenno Power Страницы: 2

Бренд: cleanAIR Страницы: 15

Challenger 2013

Бренд: Dodge Страницы: 543

Бренд: Intelbras Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды